TEMP Button :
Push this button to decrease the indoor
o
O
temperature setting in 1 F increments to 62 F.
FP Button:
During the heating operation(only when the
setting mode is HEAT), press this button and the unit will
operate at high fan speed with the temperature automatically
O
O
set to 8 C/46 F. The display window of indoor unit will display
FP . Press the buttons of ON/OFF, MODE, FAN SPEED,
TEMP UP/DOWN, TIMER ON/OFF, SLEEP or FP while
operating will cancel the FP function.
RESET Button:
When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
SLEEP Button:
Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
2
1
6
ON/OFF Button:
Push this button to start operation, push
the button again to stop operation.
9
TEMP Button :
Push this button to increase the indoor
o
O
temperature setting in 1 F increments to 86 F.
2
AIR DIRECTION Button:
Used to change the louver
movement and set the desired up/down air flow direction.
O
The louver changes 6 in angle for each press.
MODE Selection Button:
Each time the button is pressed,
the operation mode is shifted in the direction of the arrow:
AUTO
COOL
DRY
HEAT
FAN
3
FAN SPEED Button:
Used to select the Fan Speed in four steps-
AUTO LOW
MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button:
Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10h, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0.0.
10
11
4
5
NOTE:
While the unit is running under SLEEP operation mode, it would
be canceled if you press the MODE,FAN SPEED or ON/OFF button.
SWING Button:
Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
7
NOTE
Please do not select HEAT mode if the machine you
purchased is cooling only type. Heat mode is not supported by
the cooling only appliance.
NOTE:
Press and hold and buttons together for 3 seconds will
O
O
alternate the temperature display between the C & F scale.
3
TIMER OFF Button:
Press this button to initiate the auto-off time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10h, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-off time
to 0.0
12
1
2
5
4
6
4
3
Indicators on Display Panel
Display Panel
TRANSMI-
SSION Indicator
OPERATION
MODE Indicator
LOCK Indicator
TIMER
DISPLAY Indicator
DIGITAL
DISPLAY area
ON/OFF Indicator
FAN SPEED Indicator
TIMER ON OFF
DIGITAL DISPLAY area:
This area will show the set temperature
and, if in the TIMER mode, will show the ON and OFF settings of
the TIMER. If in the FAN mode, nothing is appeared.
TRANSMISSION Indicator:
This indicator flashes one time
when remote controller transmits signals to the indoor unit.
Fig. 2
1
2
LOCK Button:
When you press the recessed LOCK button, all
current settings are locked in and the remote controller does not
accept any operation except that of the LOCK. Press again to
cancel the LOCK mode.
13
TURBO Button:
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset temperature at cooling or
heating operation in the shortest time(if the indoor unit has no
this function, there is no corresponding operation happened
when press Turbo button.)
14
15
OPERATION
MODE Indicator
7
LED DISPLAY Button:
Press this button to clear the digit
display in the air conditioner, press it again to illuminate (Not
available for the units without LED display window).