Sentex Crown Jewel Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 24

Sentex Crown Jewel Скачать руководство пользователя страница 13

13

EXIT

EXIT

A

UT

OCALL

TB3 PHONE LINE

TB5

TB4

COM

PM1

PM2

HOUSE TELCO

DS1

EARTH GND

8

Exit 2

N

C (

N

ormally Closed)

COM (Common)

COM (Common)

Use 1

8

-24 A

W

G

WIRING A DOOR SENSING DEVICE

The unit can monitor the position of one entrance and will react to a change in the door’s status (Relay #2
must be set as a shunt, alarm or CCTV relay, it cannot be set as a control relay). For example, if a door is
held open after the relay deactivates or is pried open. The unit can:

• Call the main residence telephone and report the status of the door.
• Close Relay #2 to activate a device such as a light, CCTV camera or siren.

NOTE:

You must enable the Alarm Call feature, see the Keypad Programming manual for information.

BASIC WIRING (CONTINUED)

EXIT

EXIT

A

UT

OCALL

TB3 PHONE LINE

TB5

TB4

COM

PM1

PM2

HOUSE TELCO

DS1

EARTH GND

8

Exit 2

COM (Common)

Use 1

8

-24 A

W

G

Loop Sensor

Loop
Detector

WIRING AN AUTO-CALL SENSOR

The Auto-Call feature will enable the unit to contact the residence when a driveway sensor (or any device that
provides a contact closure) is activated.

«
...
11
12
13
14
15
...
»

Содержание Crown Jewel

























Отзывы:

Нет отзывов