SenTech STC-MBS322U3V Скачать руководство пользователя страница 33

Страница: 33 / 65

No.15S103-01

33/65

STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V

Specifications and Use

’s guide

Exposure Start trigger determines exposure start timing, Exposure End trigger determines exposure end timing.

To operate the camera under this mode, the following settings have to be set.

・

Exposure Mode: Trigger Controlled

・

Selects Trigger Selector: Exposure Start, and Trigger Mode: On

・

Selects Trigger Selector: Exposure End, and Trigger Mode: On

(*) On Trigger Mode except Frame Start should be set Off.

Timing

(*)When all of Trigger Mode (Frame Start trigger, Exposure Start trigger, Exposure End)

are On, camera’s behavior

depends on Exposure Mode setting.
When the Exposure Mode sets the Trigger Control, this function works through Trigger Start/End Trigger
This function works through Frame Start trigger for the remainder of the Exposure Mode.

This function can apply either external signal or a software command as the trigger.
The software trigger can be applied through

the “execute Trigger Software” command when the trigger is

selected on the Trigger Selector.

ExposureStartトリガー

ExposureStopトリガー

I/O遅延(tIPDLH)

露光

映像出力

LineDebounceTime

TriggerDelay

I/O遅延(tIPDLH)

LineDebounceTime

TriggerDelay

センサー内部の露光開始遅延

Exposure

VideoOut

Trigger Input

(Positive)

Trigger Input

(Negative)

I/O Delay(tIPDLH)

Exposure Start Duration

inside of sensor

I/O Delay(tIPDLH)

Exposure Start Duration

inside of sensor

Содержание STC-MBS322U3V


































































Результаты поиска

Содержание STC-MBS322U3V

Отзывы:

Похожие инструкции для STC-MBS322U3V

Бренды по названию

Популярные бренды

SenTech STC-MBS322U3V, Технические характеристики

Результаты поиска

Содержание STC-MBS322U3V

Отзывы:

Похожие инструкции для STC-MBS322U3V

Бренды по названию

Популярные бренды