sensonor STIM210 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 20

sensonor STIM210 Скачать руководство пользователя страница 4

USER MANUAL

EvaluationTools

STIM210 Evaluation Kit - USB

DOK452 rev.0

4/20 2020

4.1

USB kit Installation of FTDI serial driver

To install the drivers for the FTDI serial driver under Windows, follow the instructions below:



Connect the USB-RS422 plug to a spare USB port on your PC.



If there is an available Internet connection, some Windows versions will silently connect to the Windows
Update website and install a suitable driver



In the event that no automatic installation takes place, please refer to the set-up guide from FTDI:

http://www.ftdichip.com/Support/Documents/InstallGuides.htm

4.2

Verification and configuration of serial driver

Launch

Device Manager

. See

Control Panel

->

Hardware and Sound -> Devices and Printers

.

Verify that the driver installation has completed successfully:

Figure 1: COM port assignments for USB cable in Windows 7.

Make a note of the assigned COM port value(s) information. This will be needed later for connecting to the STIM210
from the PC software.

Right-click "USB Serial Port (COM<n>)" and select "Properties"

«
...
2
3
4
5
6
...
»

Содержание STIM210





















Отзывы:

Нет отзывов