SENSIT Technologies GOLD CGI Скачать руководство пользователя страница 1

 750-00035  INSTRUCTION MANUAL     REV. 9/15/10

SENSIT TECHNOLOGIES
851 Transport Drive
Valparaiso, IN 46383
Phone: (219) 465-2700
Fax: (219) 465-2701
Order Line: (888) 473-6748
www.gasleaksensors.com

WARRANTY

Your Sensit®Gold CGI is warranted to be free from defects in
materials and workmanship for a period of two years after pur-
chase (excluding  calibration and batteries). The % gas sensor
(TC) is warranted for 5 years. If within the warranty period, your
instrument should become inoperative from such defects, the
unit will be repaired or replaced at our option. This warranty cov-
ers normal use and does not cover damage which occurs in
shipment or failure which results from alteration, tampering, ac-
cident, misuse, abuse, neglect or improper maintenance. Proof
of purchase may be required before warranty is rendered. Units
out of warranty will be repaired for a service charge. Internal
repair or maintenance must be completed by a SENSIT Tech-
nologies authorized technician. Violation will void warranty. Units
must be returned postpaid, insured and to the attention of the
Service Dept. for warranty or repair.

This warranty gives you specific legal rights and you may have
other rights which vary from state to state.

SENSIT Technologies

851 Transport Drive

Valparaiso, IN 46383

Phone: (219) 465-2700

888 4 SENSIT (473-6748)

Fax: (219) 465-2701

www.gasleaksensors.com

SENSIT®GOLD CGI

For use  with combustible gases
and optionally  available
oxygen and toxic gases.

INSTRUCTION MANUAL

Read and understand
instructions before use.

Approved UL913, For Class 1,
Division 1, Groups C & D, T3
hazardous locations when used
with alkaline or NiMH batteries.

7WA6

C

LA

SSI

FIE

D

      Warning:
To prevent ignition
of flammable or
combustible
atmospheres,
disconnect power
before servicing.

A

P

O

W ER

C

SA

VE

B

M

E N U

B

TES

T

SENSIT GOLD CGI

®

GAS

Содержание GOLD CGI





















Отзывы: