manualshive.com logo in svg

SenseAir aSENSE mIII, Руководство пользователя

Поделиться
Скачать
SenseAir aSENSE mIII Скачать руководство пользователя страница 11

 

 

 

 

 

Dokument 
 

UMA0132

 

Rev 

3

 

Sid 
11 (16)

 

 

 

 
4. 

Push ENTR(+-) once. The display shows EC and two digits. Enter the access 

code  to  the  service  menu.  If  the  default  code  is  used  do  like  this:  Push 
MENU(+) until the digits stop. The display shows EC55. If the correct code is 
not entered before the time limit exceeds the sensor returns to DEFAULT. 

 
5. 

Push  ENTR(+-)  once.  The  display  shows  SPCO  to  set  the  carbon  monoxide 
set point. 

 

6. 

Push ENTR(+-)  once.  The  display  shows  the  carbon monoxide  set point  e.g. 
ex 35 ppm. Push MENU(+) to increase the set point value in steps of 1 ppm.  

 

Push ESC(-) to decrease the set point value in steps of 1 ppm. 

 
7. 

Push ENTR(+-) once when the set point is set. The display shows SPCO.  

 

Push ESC(-) to return to DEFAULT. 

 
8. 

Push MENU(+) once to reach the carbon dioxide set point.  

 

The display shows SP C. 

 
9. 

Push ENTR(+-) once. The display shows the carbon dioxide set point e.g. 750 
ppm. Push MENU(+) to increase the set point value in steps of 50 ppm.  

 

Push ESC(-) to decrease the set point value in steps of 50 ppm. 

 
10. 

Push ENTR(+-) once when the set point is set. The display shows SP C.  

 

Push ESC(-) to return to DEFAULT. 

 
11. 

Push MENU(+) once to reach the setting of analogue outputs.  

 

The display shows AOUt. 

 
12. 

Push ENTR(+-) to reach the output to be set. The display shows An and two 
digits e.g. An 01. Step to the requested output by pushing MENU(+). 

 
13. 

Push ENTR(+-) to reach the setting of the MIN value. The display shows Set 
L. 

 

14. 

Push  ENTR(+-)  to  set  the  MIN  value  of  the  output.  The  display  shows  the 
numerical value in  %  e.g.  the standard setting 0.0 % or previously set  value. 
Push MENU(+) to increase the MIN value. Push ESC(-) to decrease the MIN 
value.  Push  ENTR(+-).  The  display  shows  Sure.  Push  ENTR(+-)  to  save  the 
setting and return to Set L. Push MENU(+) or ESC(-) to return to Set L without 
saving the new setting. 

 

15. 

Push MENU(+) to reach the setting of the MAX value. The display shows Set 
H. 

 

16. 

Push  ENTR(+-)  to  set  the  MAX  value  of  the  output.  The  display  shows  the 
numerical value in % e.g. the standard setting 100.0 % or previously set value. 
Push MENU(+) to increase the MAX value. Push ESC(-) to decrease the MAX 
value.  Push  ENTR(+-).  The  display  shows  Sure.  Push  ENTR(+-)  to  save  the 

Содержание aSENSE mIII

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды