background image

Product Introduction

 

 

  SP2nd is Simple Gas Alarm Detector that is required to protect users’ safety at 

dangerous  work  environments.  The  apparatus  can  indicate  simultaneously  the 

concentration of gases (Oxygen, Carbon Monoxide, Hydrogen Sulfide, Hydrogen, 

Sulfur Dioxide, Hydrogen Chloride, Ammonia and etc.) on a digital LCD monitor, 

and the methods of operation and calibration are easy and convenient.   

  This  instrument  alerts  accurately  the  alarm  circumstances  to  operators  and 

workers  for  their  safety  with  its  functions  of  loud  alarm  sound  and  vibration, 

when higher gas concentration than normality is detected. Besides, it is available 

for  users  to  check  upon  occasion  and  adjust  the  value  of  alarm  to  the  work 

environment  on  demand,  since  it  has  the  function  of  indicating  minimal  and 

maximal  concentration  of  the  gases.  It  is  also  possible  to  prevent  in  advance 

workers from the danger of exposing for a definite period of time to such toxic 

gases  as  Hydrogen  Sulfide(H

2

S),  Carbon  Monoxide(CO)  and  Sulfur  Dioxide(SO

2

by  its  function  of  STEL(Short  Term  Exposure  Limit)  and  TWA(Time  Weighted 

Average). 

Guarantee and Repair  

 

  Senko Co., Ltd. guarantees the products of SP series for 24 months from the 

shipping  date  and  repairs  or  replaces  the  defected  product  during  warranty 

period at no cost.  Nevertheless, Senko is not responsible for the following cases 

and  would  not  repair  or  replace  the  product  at  no  cost,  such  cases  as  the 

product has been purchased through the route that Senko does not approve, or 

as the product has been damaged or deformed mechanically by misuse of the 

user, or as the product has not been calibrated or replaced the parts according 

to processes in the operating manual. 

  In the event that any defect or issue of the product occurred during warranty 

period,  Senko  will  cover  all  the  expenses  except  transportation  fee.    After  the 

period  of  warranty,  the  expenses  of  repair  or  replacement  of  the  product  and 

transportation  will  be  in  principle  borne  by  the  user.    Senko  will  not  be 

responsible  for  any  indirect  occurrence  or  accident  and/or  damage  during  the 

use  of  the  product,  and  the  guarantee  shall  be  limited  to  the  replacement  of 

parts and product.  The guarantee is applied only to the users who purchased 

the product at Senko’s authorized dealers or agents, and the guarantied repair is 

to be performed by the expert engineers of Senko’s authorized aftercare center. 

01 

Содержание SP12C7






















Отзывы: