3
Setting Up
▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪
Setting Up
The.CSP-series.speakers.are.designed.for.easy.installation..If.
necessary,.installation.can.be.accomplished.without.access.above.
the.ceiling.
Tools needed for installation
▪
Drywall.saw
▪
Slotted.screwdriver
▪
Phillips.head.screwdriver
▪
Wire.stripper
▪
Pencil
Preparing the ceiling
Drop Ceilings
1
....Locate.the.ceiling.tile.in.which.the.speaker.is.to.be.mounted.and.
remove.the.tile.from.the.ceiling..
2
....Measure.to.find.the.center.of.the.tile.and.place.a.mark.there..Use.
that.mark.to.center.the.cutout.template.on.the.tile..With.a.pencil,.
trace.an.outline.of.the.cutout.template.on.the.tile.
3
....Use.a.drywall.saw.to.cut.along.the.traced.
line.
.
Pro tip:
For.easy.cleanup.it’s.best.to.
perform.this.step.while.placing.the.tile.over.
an.open.box.or.trashcan.
4
....Replace.the.ceiling.tile.into.the.ceiling.
5
....Insert.the.rails.through.the.hole.
6
....Place.the.rails.on.either.side.of.the.hole.so.that.the.inverted.“V”.
ends.of.the.rails.fit.over.the.ceiling.grid.rails..The.flat.side.of.the.
rails.should.rest.on.the.tile,.and.the.side.with.the.pre-cut.holes.
should.stand.perpendicular.on.either.edge.of.the.hole.
.
Note:
The.rails.of.the.mounting.bracket.do.not.attach.to.the.
ceiling.grid.rails,.but.suspend.over.them.
7
....Insert.the.C-ring.by.angling.
it.through.the.hole.using.
the.open.end.of.the.ring.
8
....Fit.the.slots.of.the.C-ring.over.the.
rails.and.attach.it.by.inserting.the.
bolts.through.the.tabs.of.the.C-ring.
and.securely.tightening.the.nuts.
9
....Pull.the.speaker.wire.out.so.that.it.
extends.beyond.the.ceiling.and.gives.
you.enough.length.to.complete.the.
installation.
Fixed Ceilings
1
....Locate.the.spot.where.the.speaker.will.be.installed
2
....Use.a.stud.finder.to.locate.studs.in.the.ceiling..Make.sure.they.
won’t.interfere.with.your.installation..If.a.stud.is.near.the.location.
of.your.hole,.make.sure.that.there.is.1-inch.clearance.between.the.
edge.of.the.hole.and.the.stud.
Pro tip:
.Drill.a.small.pilot.hole.and.probe.inside.the.ceiling.with.
a.stiff.wire.to.make.sure.there.are.no.obstructions.where.you.are.
planning.on.placing.the.speaker.
3
....With.a.pencil,.trace.an.outline.of.the.cutout.template.on.the.
ceiling.
4
....Use.a.drywall.saw.to.cut.along.the.traced.line.and.remove.the.
cutout.from.the.ceiling..
5
....Pull.the.speaker.wire.out.so.that.it.extends.beyond.the.ceiling.
and.gives.you.enough.length.to.complete.the.installation.
Connecting the wiring to the removable locking
connector
CSP-162
1
....Open.the.connector.cover.plate.door.
2
....Remove.the.locking.connector.from.the.
socket
3
....Strip.approximately.1/4
"
.(6.mm).off.the.
ends.of.the.insulation.on.the.speaker.
wires.
4
....Insert.the.exposed.ends.of.the.wires.
into.the.connector.and.tighten.the.
screw-down.terminals.using.a.small.flat.blade.
screwdriver.
CSP-142
1
....Remove.the.cover.by.unscrewing.the.two.
screws.attaching.it.to.the.backcan.
1.1.
...Determine.the.angle.your.speaker.
wires.approach.the.speaker.and.
remove.the.appropriate.knockout.
1.2.
.Feed.the.wires.through.the.
knockout.
2
....Remove.the.locking.connector.from.the.
socket
3
....Strip.approximately.1/4
"
.(6.mm).off.the.
ends.of.the.insulation.on.the.speaker.
wires.
4
....Insert.the.exposed.ends.of.the.wires.into.
the.connector.and.tighten.the.screw-
down.terminals.using.a.small.flat.blade.
screwdriver.
Inside-ceiling view
of assembled rails
and C-ring.
Содержание CSP-142
Страница 8: ...GG2 www senalsound com...
