manualshive.com logo in svg

Select Engineered Systems Select Gate 1A, Руководство пользователя/инсталлятора

Поделиться
Скачать
Select Engineered Systems Select Gate 1A Скачать руководство пользователя страница 42

I.

FCC REQUIREMENTS

1.

The Federal Communications Commission (FCC) has established Rules which permit this
device to be directly connected to the telephone network.  Standardized jacks are used for
these connections.  This equipment should not be used on party lines or coin lines.

2.

If this unit is malfunctioning, it may also be causing harm to the telephone network; this
device should be disconnected until the source of the problem can be determined and until
repair has been made.   If this is not done, the telephone company may temporarily
disconnect service.

3.

The telephone company may make changes in its technical operations and procedures; if
such changes affect the compatibility or use of this device, the telephone company is
required to give adequate notice of the changes.  You will be advised of your right to file a
complaint with the FCC.

4.

If the telephone company requests information on what equipment is connected to their
lines, inform them of:

a.

The telephone number this unit is connected to

b.

The ringer equivalence number

c.

The USOC jack required

d.

The FCC Registration number

Items `b' and `d' are indicated on the label.

The ringer equivalence (REN) is used to determine how many devices can be connected to

your telephone line.  In most areas, the sum of the RENs of all devices on any one line should not
exceed five (5.0).  If too many devices are attached, they may not ring properly.

Содержание Select Gate 1A

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды