Selbach BT 40 Скачать руководство пользователя страница 10

10 

Mechanical cleaning: 

 

For the part of the appliance containing the tube, sponge balls are pushed in alternate flow direction through the 
line with the help of cold water. However, this requires that the tube has an even diameter and does not contain 
any interfering fixtures. 

 
 

 
 
 

Frequent use removes deposits forming inside the beer line substantially by means of mechanical friction. 
Mechanical cleaning can remove germs from the line, however, does nothing to inhibit their growth.  For that 
reason, at certain intervals chemical cleaning is also required. 
 
Store balls safely at a place where they are protected against contamination. DIN 6650 stipulates the single 
use of cleaning balls as micro organisms may grow inside the damp sponge. 

 

 
 
Only use mild detergents and a damp cloth for cleaning. 
The water cooling element and water-conducting components may only be cleaned with beverage 
dispenser approved detergents. 

 
 
 

Do not allow any moisture to get inside the device. 

 

 

 
 

Mechanical Bevi 
cleaning device 

Comprehensive cleaning set 
for mechanical cleaning 

Schematic view 
of mechanical 
cleaning  

Содержание BT 40













Отзывы: