background image

HANDLING PRECAUTIONS

1

1

HANDLING PRECAUTIONS

1

•  Before performing work, be sure to turn the power off. Performing the work 

without turning the power off can cause an electric shock or short circuit. In the 

case work should be performed in the status of power on, this manual always 

states to that effect.

•  To avoid an electric shock or short circuit, do not plug in or unplug quickly.
•  To avoid an electric shock, do not plug in or unplug with a wet hand.
•  Do not expose power cords or earth wires on the surface, (floor, passage, etc.). If 

exposed, the power cords and earth wires are susceptible to damage. Damaged 

cords and wires can cause an electric shock or short circuit.

•  To avoid causing a fire or an electric shock, do not put things on or damage the 

power cords.

•  When or after installing the product, do not unnecessarily pull the power cord. If 

damaged, the power cord can cause a fire or an electric shock.

•  In case the power cord is damaged, ask for a replacement through where the 

product was purchased from or the office herein stated. Using the cord as is 

damaged can cause fire, an electric shock or leakage.

•  Be sure to perform grounding appropriately. Inappropriate grounding can cause 

an electric shock.

•  Be sure to use fuses meeting the specified rating. Using fuses other than the 

specified rating can cause a fire or an electric shock.

•  Be sure that connections such as IC BD are made properly. Insufficient insertion 

can cause an electric shock.

•  Specification changes, removal of equipment, conversion and/or addition, not 

designated by SEGA are not permitted.

   - Failure to observe this may cause a fire or an electric shock. Non-compliance 

with this instruction can have a bad influence upon physical conditions of the 

players or the onlookers, or result in injury during play.

   - SEGA shall not be held responsible for damage, compensation for damage to a 

third party, caused by specification changes not designated by SEGA.

•  Do not perform any work or change parts not listed in this manual. Doing so may 

lead to an accident.

  If you need to perform any work not listed in this manual, request work from the 

office indicated in this manual or the point of purchase, or inquires for details.

•  Be sure to perform periodic maintenance inspections herein stated.

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that 

the player can enjoy the game safely.

Non-compliance with the following points or inappropriate handling running counter to the cautionary matters 

herein stated can cause personal injury or damage to the machine.

Содержание Clay Challenge



































































Отзывы: