LSHVD1S Series Inverter Unit
8
OPERATION cont.
TEMP
Press the TEMP button to toggle
between the following on the indoor
display:-
SET temperature (room target
temperature). SET temperature
is displayed if no icon is shown.
Indoor ambient temperature
Outdoor ambient temperature
(where equipped)
Note:
outdoor temperature display is not
available on some models.
default setting is ‘no display’
Only available on models with a
‘dual 8' display on the indoor unit.
When in COOL, HEAT or DRY modes,
press the SLEEP button to start up the
sleep function.
The
icon is displayed on the
remote controller. Default setting is
SLEEP mode ‘OFF’.
In COOL and DRY modes, after
running for one hour, the main unit
SET temperature will increase by 1°C,
then after 2 hours will increase by 2°C,
then will continue to run at this
temperature.
SLEEP
SLEEP cont.
cancel
CHILD LOCK
In HEAT mode, the SET temperature
will decrease by 1°C and then 2°C for
the first 2 hours, and then stay
constant.
Press the I FEEL button to activate this
feature. The remote controller will act
as the temperature thermostat,
sending a temperature reading to the
unit every 10 minutes. By this method,
the unit will react to where the remote
controller is positioned. I FEEL will be
shown on the remote controller
display.
Press the I FEEL button again to
this feature.
The remote controller can be locked
from inadvertent button operation.
I FEEL
FAHRENHEIT / CENTIGRADE
Press both
or
buttons
simultaneously to lock (or unlock) the
remote controller. The
icon will
be displayed, and will blink 3 times
when a button is pressed.
The temperature display can be
toggled between Centigrade and
Fahrenheit scales by pressing the
d
buttons simultaneously
while in ‘OFF’ status.
8
BSHVD1S Series High Wall Inverter Unit
I FEEL
Press the I FEEL button to activate this
feature. The remote controller will act
as the temperature thermostat,
sending a temperature reading to the
unit every 10 minutes. By this method,
the unit will react to where the remote
controller is positioned. The
icon
will be shown on the remote controller
display.
Press the I FEEL button again to
this feature.
Press SLEEP button to toggle between
the SLEEP modes and cancel, as
described below. Default setting is
SLEEP mode ‘OFF’:-
In COOL and DRY modes,
after running for one hour, the main
unit SET temperature will increase by
1°C, then after 2 hours will increase by
2°C, then will continue to run at this
temperature.
In HEAT mode, the SET temperature
will decrease by 1°C and then 2°C for
the first 2 hours, and then stay
constant.
In COOL mode, the SET
temperature will vary according to the
below scenarios:-
a) If SET temperature starts between
16-23°C, SET temperature will
increase by 1°C every hour for 3
hours, then stay constant until 7 hours
cancel
SLEEP
SLEEP 1:
SLEEP 2:
SLEEP cont.
has elapsed. It will then be decreased
by 1°C, then will continue to run at this
temperature.
b) If SET between 24-27°C, SET
temperature will increase by 1°C every
hour for 2 hours, then stay constant
until 7 hours has elapsed. It will then
be decreased by 1°C, then will
continue to run at this temperature.
c) If SET between 28-29°C, SET
temperature will increase by 1°C for 1
hour, then stay constant until 7 hours
has elapsed. It will then be decreased
by 1°C, then will continue to run at this
temperature.
d) If SET at 30°C, SET temperature
will stay constant until 7 hours has
elapsed. It will then be decreased by
1°C, then will continue to run at this
temperature.
In HEAT mode:-
a) If SET at 16°C, it will remain at this
temperature.
b) If SET between 17-20°C, SET
temperature will decrease by 1°C for 1
hour, then will continue to run at this
temperature.
c) If SET between 21-27°C, SET
temperature will decrease by 1°C for 2
hours, then will continue to run at this
temperature.
OPERATION cont.
