manualshive.com logo in svg

SeeedStudio BeagleBone Green, Справочное руководство, Страница: 16 / 26

Поделиться
Скачать
SeeedStudio BeagleBone Green Скачать руководство пользователя страница 16

 

REF: BBONEGRN_SRM                   

BeagleBone Green   

                  System  Reference  Manual                             

Rev  v1     

 

 

16 

5.2

 

Processor 

Sitara AM3358BZCZ100   

5.3

 

Memory   

Described in the following sections are the three memory devices found on the board. 

 

5.3.1

 

512MB DDR3L   

A single 256Mb x16 DDR3L 4Gb (512MB) memory device is used. The memory used is is 
one of two devices: 

 

- MT41K256M16HA-125 from Micron   
- D2516EC4BXGGB from Kingston 

 

It will operate at a clock frequency of 400MHz yielding an effective rate of 800MHZ on the 
DDR3L bus allowing for 1.6GB/S of DDR3L memory bandwidth. 

 

5.3.2

 

4KB EEPROM   

A  single  4KB  EEPROM  is  provided  on  I2C0  that  holds  the  board  information.  This 
information includes board name, serial number, and revision information. This is the not 
the same as the one used on the original BeagleBone. The device was changed for cost 
reduction reasons. It has a test point to allow the device to be programmed and otherwise 
to provide write protection when not grounded. 

 

5.3.3

 

4GB Embedded MMC   

A single 4GB embedded MMC (eMMC) device is on the board. The device connects to the 
MMC1  port  of the processor,  allowing for  8bit wide  access.  Default  boot mode for  the 
board will be MMC1 with an option to change it to MMC0, the SD card slot, for booting 
from the SD card as a result of removing and reapplying the power to the board. Simply 
pressing the reset button will not change the boot mode. MMC0 cannot be used in 8Bit 
mode because the lower data pins are located on the pins used by the Ethernet port. This 
does not  interfere  with SD  card  operation but  it  does  make  it  unsuitable  for  use  as  an 
eMMC port if the 8 bit feature is needed.   

5.3.4

 

MicroSD Connector   

The  board  is  equipped  with  a  single  micro  SD  connector  to  act  as  the  secondary  boot 
source  for  the  board  and,  if  selected  as  such,  can  be  the  primary  boot  source.  The 
connector will support larger capacity micro SD cards. The micro SD card is not provided 

Содержание BeagleBone Green



























Отзывы:

Нет отзывов