ENFORCER Hands-Free Video Door Phone
8
SECO-LARM U.S.A., Inc.
Troubleshooting:
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]
PICRN4
MI_DP-264-1C7Q_200610.docx
NOTICE:
The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of
SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A., Inc. All rights reserved.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for
one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective
part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God,
physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason
SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind
to the purchaser or anyone else.
IMPORTANT:
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM
will not be held responsible for the use of this product in
violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted.
Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to
operate the device.
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
Check that the wiring distance does not exceed 230ft (70m)
The screen image is dim.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate
The screen image has poor color tone
or flickers
Adjust the monitor’s color tone.
Adjust the monitor’s brightness.
Change the position of the camera.
Use untwisted wire and make sure the wiring distance does
not exceed 230ft (70m)
The screen image is distorted.
Change the position of the camera.
Use untwisted wire and make sure the wiring distance does
not exceed 230ft (70m)
Check End-of-Line resistor jumper is adjusted correctly on all
monitor
The camera case is hot.
Check that the correct power supply is in use.
LEDs do not turn on.
Check that the correct power supply is in use (18VDC).
Check that the wiring distance does not exceed 230ft (70m)
Lock button does not operate the relay
Check that the correct power supply is in use (18VDC).
Check that the wiring distance does not exceed 230ft (70m)
