ENFORCER HDMI Surge Protector
2
SECO-LARM U.S.A., Inc.
To HDMI
Input
Unprotected
End
1" (26mm)
To HDMI
Output
Protected
End
2
3
/
16
" (56mm)
Grounding Wire
Attachment Location
*
(One on each end)
1" (26mm)
*
Note:
There is a ‘Grounding Wire Attachment Location’ included on both ends of the HDMI Surge
Protector. Grounding wire can be attached to either of these locations.
Introduction:
The ENFORCER HDMI Surge Protector is a passive device that helps protect sensitive HDMI
equipment from power surges. The device can be deployed in new installations or existing
ones.
The ENFORCER HDMI Surge Protector should be installed between HDMI equipment such as
players, monitors, and projectors to protect against surges that could damage the video
equipment.
NOTE
: For the best protection, installing two surge protectors is recommended: one at each
end of the cable.
ESD protection
15kV (ESD), 8kV (Contact)
EFT protection
40A (5/50ns)
Surge protection
5A (8/20ns)
Surge reaction speed
<1ns
Connector
In
HDMI
Out
HDMI
Dimensions
2
3
/
16
"x1"x1" (56x26x26 mm)
Weight
1.2-oz (35g)
Material
Aluminum
Operating temperature
32°~131°F (0°~55° C)
Specifications:
Overview:
1x HDMI Surge Protector
2x Mounting screws
1x 12" (30cm) grounding wire
1x Manual
2x Plastic wall anchors
1x Grounding wire screw
Parts List:
ENFORCER HDMI Surge Protector
SECO-LARM U.S.A., Inc.
3
To ground
2
(can be attached to either end of surge protector)
HDMI Player
(Not Protected)
HDMI Surge
Protector
HDMI cable
1
Protected
End
HDMI Monitor
(Protected)
Unprotected
End
Short
HDMI
cable
(Ground can be attached to either end of surge protectors)
HDMI Monitor
(Protected)
Short
HDMI
cable
HDMI Surge
Protector
HDMI Surge
Protector
HDMI cable
1
To ground
2
To ground
2
HDMI Player
(Protected)
Protected
End
Protected
End
Unprotected End
Short
HDMI
cable
Protecting Multiple Devices:
Installation:
1.
Detach the existing HDMI cable
1
from the device to be protected and attach that cable to the
“Unprotected” end of the HDMI Surge Protector.
2.
Attach another HDMI cable (not included) between the device to be protected and the
“Protected” end of the HDMI Surge Protector. The protected cables should be as short as
possible and should not cross unprotected cables.
3.
Connect the ground wire from the HDMI Surge Protector (either end
2
) to earth ground. The
system should use a single ground point and the protected device should be isolated from
ground.
1.
Detach the HDMI cable
1
from both devices to be protected.
2.
Attach an HDMI Surge Protector to each end of the HDMI cable, ensuring that the cable is
connected to the “Unprotected” end of the HDMI Surge Protector.
3.
Attach another HDMI cable (not included) between each device to be protected and the
“Protected” end of its respective HDMI Surge Protector. For best protection, the protected
cables should be as short as possible and should not cross unprotected cables.
4.
Connect the ground wire from each HDMI Surge Protector (either end
2
) to earth ground. The
system should use a single ground point and the protected device should be isolated from
ground.
Protecting a Single Device:
NOTE
: These instructions assume that 2 HDMI devices have already been connected together.
1
Note:
The maximum length of the HDMI cable will depend on the cable’s specification and quality.
2
Note:
There is a ‘Grounding Wire Location’ included on both ends of the HDMI Surge Protector.
Grounding wire can be attached to either of these locations.