SECO-LARM ENFORCER E-964-Q165Q Скачать руководство пользователя страница 6

Страница: 6 / 12

Fig. 7:
Pole Mount

Wiring the Transmitter
– Pole Mount

(NOTE – Pole mounting bracket included.)
1. Remove the cover. Remove the screw under

the lens unit in order to detach the mounting

plate. See fig. 4.

2. Break a hole in the mounting plate’s rubber

grommet, and pull the cable through the

grommet’s hole. Then run the cable through

the hole near the bottom of the sensor unit so

it comes out the front. Use the included

mounting bracket to mount to the pole. Then

reattach the sensor unit to the mounting plate,

connect the wires, and snap on the cover.
See fig. 7.

Wiring (fig. 8)

1. Screw the wires tightly to avoid slipping off the

terminals, but not so tight that they break.

2. Screws on terminals which are not used

should be tightened.

3. Grounding may be necessary, depending on

the location.

Wiring the Transmitter – Wall Mount

1. Remove the cover. Remove the screw under the

lens unit in order to detach the mounting plate.

See fig. 4.

2. If the sensor wiring comes from inside the wall –

Break a hole in the mounting plate’s rubber

grommet, and pull the cable through the

grommet’s hole. Then run the cable through the

hole near the bottom of the sensor unit so it

comes out the front. Using two of the included

mounting screws, attach the mounting plate to

the wall. Then reattach the sensor unit to the

mounting plate, connect the wires, and snap on

the cover. See fig. 5.

3. If the sensor wiring is run along the surface of the

wall – There are four plastic knockouts on the

back of the sensor unit, two on top and two on

bottom. Break out the appropriate knockout, and

pull the wiring through the knockout. Then run the

wiring through the hole near the bottom of the

sensor unit so it comes out the front. Using two of

the included mounting screws, attach the

mounting plate to the wall. Then reattach the

sensor unit to the mounting plate, connect the

wires, and snap on the cover. See fig. 6.

Fig. 5:
Wall Mount,
Wire from
Inside Wall

Fig. 6:
Wall Mount,
Wire Runs
Along Wall

– or –

Fig. 4:
Remove the
Transmitter
cover

SECO-LARM

U.S.A.

ENFORCER Quad-Photobeam Detectors

Содержание ENFORCER E-964-Q165Q













Результаты поиска

Содержание ENFORCER E-964-Q165Q

Отзывы:

Похожие инструкции для ENFORCER E-964-Q165Q

Бренды по названию

Популярные бренды

SECO-LARM ENFORCER E-964-Q165Q, Руководство пользователя

Результаты поиска

Содержание ENFORCER E-964-Q165Q

Отзывы:

Похожие инструкции для ENFORCER E-964-Q165Q

Бренды по названию

Популярные бренды