unit disables the flashing beacon, the automatic closing stage
and the radio controls.
PROGRAMMING:
SEL button: selects the type of function to be stored; selection
is indicated by a flashing LED.
The desired function can be selected by pressing the button
repeatedly. The selection remains active for 10 seconds
(indicated by the flashing LED); after 10 seconds, the control
unit returns to its original status.
SET button: programmes the information according to the type
of function selected previously using the SEL button.
IMPORTANT: The function of the SET button can be replaced
with the radio control, if programmed previously (CODE LED
on).
MAIN MENU
The control unit is supplied by the manufacturer with the
possibility of selecting some important functions.
---------------------- MAIN MENU -----------------
Reference LED LED Off LED On
1) CODE No code Code entered
2) INB.CMD.AP Disabled Enabled
3) LAMP/CORT Flashing Courtesy light
4) T. MOT. Automatic motor time Time
programmed
5) T. PAUSA. Without aut. closing With aut.
closing
6) SEL DS1 CH = INV. AP/CH = BL
7) SEL DS2 CH = INV. AP/CH =
BL+INV.
8) SEL DS3 CH = INV. AP/CH = BL
1) CODE: (Radio control code)
The control unit can store up to 75 radio controls with different
fixed or rolling codes.
Programming using a 1- or 2-button radio control:
To programme the transmission codes in the radio control,
proceed as follows: press the SEL button and the CODE LED
will begin to flash; at the same time send the first code ("Up",
corresponding to the opening movement) on the radio control.
At this point the CODE LED will begin to flash quickly. Send the
second code (“Down”, corresponding to the closing movement)
to be stored and the CODE LED will remain lit: programming is
now complete. If the second code is not sent within 10 seconds
the control unit exits the programming stage, selecting the
function using a single button on the radio control.
Programming using a 3 button radio control in the “BeFree
Series”:
The control unit allows you to store the whole “BeFree” radio-
control by programming only the UP button.
To programme the “BeFree” radio-control codes, follow this
procedure: press the SEL button; the CODE LED begins to
flash. Press the UP button of the desired radio control at the
same time; the CODE LED will remain lit and programming will
be complete.
Deleting the codes:
To delete all transmission codes
stored in the memory, proceed as follows: press the SEL
button; the CODE LED starts flashing. Then press the SET
button; the CODE LED switches off and the procedure is
complete.
Maximum number of radio controls which can be stored:
The control unit can store up to 75 radio controls with different
fixed or rolling codes. If the maximum number of radio controls
has been reached, and a programming process started, the
control unit will indicate that the programming process has
failed by flashing all the LEDs except the CODE LED, which will
remain lit in a constant manner. After 10 seconds the control
unit exits the programming mode.
2) INB. CMD. AP: (command inhibition during opening and
pause time, if entered)
The command inhibition function during opening and pause
time, if entered, is used when automation includes the loop
detector. During opening or pause time the control unit ignores
the commands given by the loop detector, push-button station
and radio control. During the closing phase a command sent by
the loop detector, push-button station or 1-button radio control
will cause the motor direction to be inverted; if operating with a
2-button radio control the button corresponding to opening will
cause the motor direction to invert and the closing button is
ignored; if operating with a radio control in the BeFree series
the opening button causes inversion, the closing button is
ignored and the Stop button causes the motor to stop.
The control unit is supplied with the default setting of the
command inhibition function during opening and pause time not
enabled. To enable the function proceed as follows: use the
SEL button to navigate to INB.CMD.AP when the relevant LED
is flashing, then press the SET button: the INB.CMD.AP LED
lights up and remains constant. Repeat the operation to restore
the previous configuration.
3) LAMP/CORT: (Selection of flashing beacon or courtesy
light)
The control unit has an output of 230 V a/c 500 W for
connection to a flashing beacon or courtesy light.
The control unit is supplied by the manufacturer with the
flashing beacon function enabled (even when the unit is
paused). To enable the flashing beacon function proceed as
follows: use the SEL button to navigate to LAMP/CORT. when
the corresponding LED is flashing, then press the SET button:
the LAMP/CORT. LED lights up and remains constant.
Repeat the operation to restore the default configuration.
To enable the courtesy light, repeat the operation above, by
pressing the SEL button twice (LAMP/CORT LED flashes
rapidly) instead of once.
Repeat the operation to restore the
default configuration.
Flashing beacon function while the unit is paused:
The 230 V a/c output will activate every time automation takes
place, for the duration of the motor timer. If the Pause Time is
stored, the 230 V a/c output will also be active during the
Pause.
Flashing Beacon Operation:
The 230 V a/c output will
activate every time automation takes place, for the duration of
the motor timer.
Courtesy Light Operation: The 230 V a/c output will activate
for 3 minutes every time an opening command is given.
4) T. MOT:
(Motor operation time of max. 4 minutes)
The control unit is supplied by the manufacturer with the
Automatic Motor Timer enabled, this way the control unit
removes the power supply from the motor 1 second after it has
reached the motor's internal stop limit. If there is an established
motor operation time and an Automatic Motor Timer which is
disabled, proceed as follows when the shutter is closed to
perform the programming process: use the SEL button to reach
the stage where the T. MOT LED flashes, then press press the
SET button briefly; the Motor will begin the Opening cycle.
When the shutter reaches the desired position press the SET
button. The motor time is stored and the T. MOT. LED remains
lit in a constant manner.
To restore the initial configuration (with the Automatic Motor
Timer function enabled) navigate to the stage where the T.
MOT. LED is flashing then press the SET button twice within 2
seconds; the LED switches off and the operation is complete.
During programming the radio control button on the control unit
can be used instead of the SET button, if stored previously.
5) T. PAUSA:
(Programming aut. closing time of max. 4 min.)
The control unit is supplied by the manufacturer without an
automatic closing procedure. To enable the automatic closing
function proceed as follows: use the SEL button to reach the
stage where the T. PAUSA LED is flashing, then press the SET
button, wait for the desired pause time, then press the SET
