background image

9

Installation Instructions and Owner's Manual

Jackplate clearance checks MUST be completed after installation 

and before use. Failure to adhere to this warning may result in the 

loss of vessel control, leading to possible ejection from vessel 

causing property damage, personal injury and/or death.

 

1.

  With the Jackplate at its intended operating position, verify 

full steering travel through the entire trim range.

 

2.

  CAREFULLY tilt the engine and verify that no interference 

occurs as the outboard engine is tilted. Check for interference 

between the SeaStar Jackplate and the steering cylinder(s), 

tiebars, steering hoses, outboard engine, engine hoses or any 

other components.

 

3.

  If any interference exists, action must be taken to do one of 

the following:

   

a. Establish the minimum operating position of the Jackplate at 

  a height which avoids interference under these conditions. 

b. Add a tilt limiter device to the outboard engine and ensure it 

  is set to prevent the engine from reaching a position where 

  interference is possible. 

c.  Move the engine up to a higher set of mounting bolt holes.

 

WARNING

 

2.5  Clearance Checks

 

WARNING

Interference with any object MUST 

be corrected prior to use.

Содержание Seastar Jackplate

















Отзывы: