Sears CRAFTSMAN C950-52725-0 Скачать руководство пользователя страница 11

Страница: 11 / 112

1741613

ASSEMBLY

HOW TO INSTALL
THE DEFLECTOR CONROL KNOB

Assemble the

deflector control knob

onto the

deflector

Make sure

lip

on the

deflector control knob

is pointed

toward the engine.

Tighten the

nut

against the bottom of the

deflector

control knob.

Figure 10

Deflector Control Lever

Deflector Control

Knob

Nut

SNOW CHUTE ASSEMBLY

Position the snow chute to the INSIDE of the snow

chute flange. Align the three holes in the snow
chute with holes in snow chute flange (see Figure 11).

Place three 5/16-18 carriage bolts from the inside of

the chute as shown in figure 11 (hardware is found
in parts bag).

Place three 5/16-18 flat washers and three 5/16-18

nuts on the outside of the flange.

First tighten the rear carriage bolt, then tighten the

remaining two carriage bolts. Make sure all carriage
bolts are tight.

Attach the remote snow chute deflector cable

the cable chute bracket (see Figure 12) and secure
by tightening nuts (on cable) to the cable chute
bracket.

Attach the remote snow chute deflector cable to the

weld stud (on deflector) and secure in place using
a pushnut as shown in Figure 12 (pushnut is found
in hardware bag).

NOTE: Check all carriage bolts in flange for tightness.
DO NOT overtighten.

Figure 11

Figure 12

Snow Chute Deflector

Snow Chute Extension

Flange

Carriage Bolt

Flat Washer

Nut

Snow Chute Deflector Cable

Pushnut

Weld Stud

Snow Chute Deflector Cable

Cable Chute Bracket

Nuts

NOTE: Before starting step 6 make sure that the chute
deflector is in the full open position and the remote
chute lever is in the full open position.

control lever

until snug against the

nut

(see Figure 10).

Содержание CRAFTSMAN C950-52725-0

















































































































Результаты поиска

Содержание CRAFTSMAN C950-52725-0

Отзывы:

Похожие инструкции для CRAFTSMAN C950-52725-0

Бренды по названию

Популярные бренды

Sears CRAFTSMAN C950-52725-0, Руководство пользователя

Результаты поиска

Содержание CRAFTSMAN C950-52725-0

Отзывы:

Похожие инструкции для CRAFTSMAN C950-52725-0

Бренды по названию

Популярные бренды