Sears CRAFTSMAN 944.605200 Скачать руководство пользователя страница 10

Страница: 10 / 52

OPERATION

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments.
Save this manual for future reference.

FIG. 5

Our tractors conform to the safety standards of the American National Standards Institute.

THROTTLE CONTROL

: Used for starting and con trol ling

engine speed.

CHOKE CONTROL:

Used for starting a cold engine.

CLUTCH/BRAKE PEDAL

: Used for clutching and brak ing

the tractor and starting the engine.

IGNITION SWITCH

: Used for starting and stopping the

engine.

LIGHT SWITCH POSITION

: Turns the headlights on and

off.

AMMETER

: Indicates charging (+) or discharging (-) of

battery.

ATTACHMENT CLUTCH LEVER

: Used to en

gage the

mower blades, or other attachments mounted to your
tractor.

LIFT LEVER PLUNGER

: Used to release attachment lift

lever when changing its position.

ATTACHMENT LIFT LEVER

: Used to raise and lower

the mower deck or other attachments mounted to your
tractor.

PARKING BRAKE LEVER

: Locks Clutch/Brake Pedal into

the brake position.

GEARSHIFT LEVER:

Selects the speed and di rec tion of

tractor.

02032

THROTTLE
CONTROL

LIFT LEVER
PLUNGER

ATTACHMENT
LIFT LEVER

PARKING
BRAKE LEVER

GEARSHIFT LEVER

CLUTCH/
BRAKE
PEDAL

CHOKE

AMMETER

ATTACHMENT
CLUTCH LEVER

IGNITION
SWITCH

LIGHT SWITCH
POSITION

HEIGHT
ADJUSTMENT
INDICATOR

Содержание CRAFTSMAN 944.605200





















































Результаты поиска

Содержание CRAFTSMAN 944.605200

Отзывы:

Sears CRAFTSMAN 944.605200, Руководство пользователя, Страница: 10 / 52

Результаты поиска

Содержание CRAFTSMAN 944.605200

Отзывы: