Sears CRAFTSMAN 944.604931 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 56

background image

22

FIG. 24

WITH PARKING BRAKE “ENGAGED”

JAM NUT

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE AD JUST -
MENT IS NECESSARY CONTACT YOUR NEAR EST AUTHO-
RIZED SERVICE CENTER/DEPARTMENT

OPERATING
ARM

NUT “A”

1-3/4"

IDLER
PUL LEYS

MANDREL
PULLEY

MANDREL
PULLEY

FIG. 23

TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 23)

The mower blade drive belt may be replaced without tools.
Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -
• Remove mower from tractor (See “TO REMOVE

MOW ER” in this section of manual).

• Work belt off both mandrel pulleys and idler pulleys.
• Pull belt away from mower.

BELT INSTALLATION -
• Work belt around both mandrel pulleys and idler pul-

leys.

• Make sure belt is in all pulley grooves and in side all

belt guides.

• Install mower (See "To Install Mower" in this section of

manual).

SERVICE AND ADJUSTMENTS

TO CHECK AND ADJUST BRAKE

(See Fig. 24)

Your tractor is equipped with an ad just able brake system
which is mounted on the right side of the transaxle.

If tractor requires more than fi ve (5) feet to stop at highest
speed in high est gear on a level, dry concrete or paved
surface, then brake must be checked and ad just ed.

TO CHECK BRAKE
• Park tractor on a level, dry concrete or paved surface,

depress brake pedal all the way down and engage
parking brake.

• Disengage transmission by placing freewheel control

in “transmission disengaged” position. Pull freewheel
con trol out and into the slot and release so it is held in
the disengaged position.

The rear wheels must lock and skid when you try to manually
push the tractor forward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE
• Depress brake pedal all the way down and en gage

parking brake.

• Measure distance between brake operating arm and

nut “A” on brake rod.

• If distance is other than 1-3/4", loosen jam nut and turn

nut “A” until distance becomes 1-3/4". Retighten jam
nut against nut “A”.

• Engage transmission by placing freewheel control in

“trans mis sion engaged” position.

• Road test tractor for proper stopping distance as stated

above. Readjust if nec es sary. If stopping distance is
still greater than fi ve (5) feet in high est gear, further
main te nance is nec es sary. Replace brake pads or
contact a qualifi ed service center.

«
...
20
21
22
23
24
...
»

Содержание CRAFTSMAN 944.604931

























































Отзывы:

Нет отзывов

Похожие инструкции для CRAFTSMAN 944.604931

Бренд: Walker Страницы: 72

Бренд: SANLI Страницы: 16

Бренд: Simplicity Страницы: 32

Бренд: Poulan Pro Страницы: 56

Бренд: FLORABEST Страницы: 44

Commercial Front Cut Rider YHRLD211

Бренд: Yazoo Страницы: 26

Бренд: RHINO Страницы: 23

Бренд: Ego Power+ Страницы: 176

Бренд: Cub Cadet Страницы: 2

Бренд: MTD Страницы: 18

Бренд: Yard force Страницы: 45

Бренд: Cramer Страницы: 180

Бренд: Snapper Страницы: 72

Бренд: Kubota Страницы: 315

Бренд: Ferris Страницы: 1

Бренд: Ferris Страницы: 40

Бренд: Ferris Страницы: 44

Бренд: Ferris Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды