4
V. GENERAL SERVICE
• Never run machine inside a closed area.
• Never make adjustments or repairs with
the engine (motor) running. Dis con nect the
spark plug wire, and keep the wire away
from the plug to prevent ac ci den tal starting.
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep equip-
ment in good condition.
• Never tamper with safety devices.
Check their proper operation reg u lar ly.
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel spill-
age. Allow machine to cool before storing.
• Stop and inspect the equipment if you
strike an object. Repair, if nec es sary,
before restarting.
• Never attempt to make wheel height
adjustments while the engine is running.
• Grass catcher components are sub ject
to wear, dam age, and de te ri o ra tion,
which could expose moving parts or
allow objects to be thrown. Frequently
check com po nents and replace with
man u fac tur er’s recommended parts,
when necessary.
• Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when ser vic ing them.
• Do not change the engine governor set-
ting or overspeed the engine.
• Maintain or replace safety and instruc-
tion labels, as necessary.
WARNING: This lawn mower is equipped with an internal com bus tion engine and
should not be used on or near any un im proved forest-covered, brush-covered or
grass-cov ered land unless the engine’s exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it
should be maintained in effective working order by the operator.
A spark arrester for the muffl er is available through your nearest Sears Service Cen-
tre (See the REPAIR PARTS section of this manual).
ASSEMBLY / PRE-OPERATION
Read these instructions and this manual in
its entirety before you attempt to assemble
or operate your new lawn mower.
IMPORTANT: This lawn mower is shipped
WITHOUT OIL OR GASOLINE in the
engine.
Your new lawn mower has been as sem -
bled at the factory with the exception of
those parts left unassembled for shipping
pur pos es. To ensure safe and proper
op er a tion of your lawn mower, all parts
and hard ware you assemble must be tight-
ened securely. Use the correct tools as
nec es sary to ensure proper tightness. All
parts such as nuts, wash ers, bolts, etc.,
nec es sary to complete the as sem bly have
been placed in the parts bag.
TO REMOVE MOWER FROM
CARTON
1. Remove loose parts included with
mower.
2. Cut down two end corners of carton
and lay end panel down fl at.
3. Remove all packing materials except
padding be tween upper and lower
handle and padding holding operator
presence control bar to upper handle.
4. Roll lawn mower out of carton and
check carton thor ough ly for additional
loose parts.
Serial Number:
Date of Purchase:
Gasoline Capacity / Type: 1,5 Litres (Unleaded Regular)
Oil Capacity: 0,58 Litres
Oil Type (API SG–SL): SAE 30 (above 0°C/32°F); SAE 5W-30 (below 0°C/32°F)
Spark Plug: Champion RJ19HX (Gap: 0,76 mm)
Blade Bolt Torque: 35-40 ft. lbs.
• The model and serial numbers will be found on a decal on the rear of the lawn mower
housing. Record both serial number and date of purchase in space provided above.
PRODUCT SPECIFICATIONS
29
MODEL NUMBER 126T02-0372-B1
BRIGGS & STRATTON 4-CYCLE ENGINE
KEY PART
NO. NO.
DESCRIPTION
404 690272
Washer (Governor Crank)
425 690670
Screw (Air Cleaner Cover)
443 692523 Screw
(Air Cleaner Primer Base)
445 491588s Filter-Air Cleaner Cartridge
455 791960 Cup-Flywheel
456 692299 Plate-Pawl
Friction
459 281505s Pawl-Ratchet
505 691251
Nut (Governor Control Lever)
523 499621 Dipstick
524 692296 • Seal- Dipstick Tube
525 495265 Tube-Dipstick
562 691119 Bolt
(Governor Control Lever)
564 698589
Screw (Control Cover)
584 697734 Cover-Breather
Passage
585 691879 • Gasket-Breather
Passage
592 690800
Nut (Rewind Starter)
597 691696
Screw (Pawl Friction Plate)
601 791850 Clamp-Hose
(Green)
604 790703 Cover-Control
608 497680 Starter-Rewind
613 790833 Screw
(Muffl er)
615 690340 Retainer-Governor
Shaft
616 698801 Crank-Governor
617 270344s
•* Seal-O
Ring
(Intake Manifold)
621 692310 Switch-Stop
(Brake)
633 691321 * Seal-Choke / Throttle Shaft
(Throttle Shaft)
633A 693867
Seal-Choke / Throttle Shaft
(Choke Shaft)
635 66538s Boot-Spark
Plug
684 690345 Screw
(Breather Passage Cover)
689 691855 Spring-Friction
718 690959 Pin-Locating
741 795755 Gear-Timing
745 691648 Screw
(Brake)
847 692047 Dipstick/Tube
Assembly
851 493880s Terminal-Spark
Plug
868 697338 • Seal-Valve
869 691155 Seat-Valve
(Intake)
870 690380 Seat-Valve
(Exhaust)
KEY PART
NO. NO.
DESCRIPTION
871 262001 Bushing-Valve
Guide
(Exhaust Valve)
63709
Bushing-Valve Guide
(Intake Valve)
883 691881 •+ Gasket-Exhaust
921 796906 Cover-Blower
Housing
922 692135 Spring-Brake
923 796136 Brake
957 793606 Cap-Fuel
Tank
966 795259
Base-Air Cleaner Primer
968 692298 Cover-Air
Cleaner
969 690700
Screw (Blower Cover)
972 699374 Tank-Fuel
975 796611 Bowl-Fuel
1036 - - -
Label-Emissions (Available
From any Briggs & Stratton
Authorized Dealer)
1058 277039
Operator’s Manual
1059 692311
Kit-Screw / Washer
(Fuel Tank)
1095 498528
Gasket Set-Valve
1210 498144
Pulley / Spring Assembly
(Pulley)
1211 498144
Pulley / Spring Assembly
(Spring)
1329 126L02-1625-F1
Replacement Engine
1330 270962
Repair Manual
1386 790848
Vane-Air
1387 790849
Spring-Air Vane
1388 790850
Screw (Air Vane)
- - 398067
Spark Arrester
(available accessory)
*
Included in Carburetor Overhaul Kit,
Key Number 121
•
Included in Engine Gasket Set,
Key Number 358
+
Included in Valve Gasket Set,
Key Number 1095
NOTE: All component dimensions given in U.S.
inches. 1 inch = 25.4 mm