Sears Craftsman 944.364480 Скачать руководство пользователя страница 11

11

LUBRICATION

Use only high quality detergent oil rated 
with API service classification SG–SL.
Select the oil's SAE viscosity grade according 
to your expected operating temperature.

Oil fi ller cap/dipstick

Lower 
limit

Upper 
limit

Tabs

Filter

Filter

Cover

Tabs

4.   Wipe off any spilled oil from lawn 

mower or side of engine.

5.   Fill engine with oil.  The engine oil 

capacity is 18.5 oz.  If oil is not com-
 plete ly drained from engine, you may 
not need the entire container of a 20 
oz. bottle of oil.  Slowly pour 3/4 of the 
oil from the container down the oil fi ll 
spout into the engine.

6.   Wait one minute to allow oil to settle.  

Use guage on oil fi ll cap/dipstick for 
checking level.  Insert dipstick into the 
tube and rest the oil fi ll cap on the tube.  
DO NOT thread the cap into the tube 
when taking reading.

7.   Continue adding small amounts of 

oil and rechecking the dipstick until it 
reads full.  DO NOT overfi ll, or engine 
will smoke on startup.

8.   Always be sure to retighten oil dipstick 

before starting engine.

9.   Reconnect spark plug wire to plug.

AIR FILTER 

Your engine will not run properly and may 
be damaged by using a dirty air fi lter. 
Replace the air fi lter every 100 hours of 
operation or every season, whichever oc-
curs fi rst.  Service air cleaner more often 
under dusty conditions.

TO CLEAN AIR FILTER
1.   Remove cover.
2.   Carefully remove cartridge.
3.   Clean by gently tapping on a fl at sur-

face. If very dirty, replace cartridge.

 CAUTION: 

 Petroleum solvents, such as 

ker o sene, are not to be used to clean car-
 tridge. They may cause de te ri o ra tion of the 
cartridge. Do not oil car tridge. Do not use 
pres sur ized air to clean or dry car tridge.
4.   Install cartridge, then replace cover.

MUFFLER

Inspect and replace corroded muffl er as it 
could create a fi re hazard and/or dam age.

SPARK PLUG

Replace spark plug at the beginning of 
each mowing season or after every 100 
hours of operation, whichever occurs 
fi rst.  Spark plug type and gap setting 
are shown in the “PROD UCT SPEC I FI C-
A TIONS” section of this manual.

NOTE:

  Multi-viscosity oils (5W30, 10W30 

etc.) improve starting in cold weather, and 
you should check your engine oil level fre-
quently to avoid possible engine damage 
from running low on oil.
Change the oil after every 25 hours of 
operation or at least once a year if the 
lawn mower is not used for 25 hours in 
one year.
Check the crankcase oil level before 
starting the engine and after each fi ve (5) 
hours of continuous use. Tighten oil plug 
securely each time you check the oil level.

TO CHANGE ENGINE OIL

NOTE

:  Before tipping lawn mower to drain 

oil, empty fuel tank by running engine until 
fuel tank is empty.
1.   Disconnect spark plug wire from spark 

plug and place wire where it cannot 
come in contact with plug.

2.   Remove engine oil cap; lay aside on a 

clean surface.

3.   Tip lawn mower on its side as shown 

and drain oil into a suitable container. 
Rock lawn mower back and forth to re-
move any oil trapped inside of engine.

Содержание Craftsman 944.364480

























Отзывы: