Note:
Maintenance and repair must only be carried out by qualified person. Contact your Sealey dealer for details.
5.1.
Lubricate all moving parts at regular intervals.
5.2.
Always keep the press clean, dry, and protected from harsh conditions.
5.3.
Should you need to replace oil ensure piston is fully retracted. An excess of oil will render press inoperative. Use only appropriate
Sealey hydraulic oil. DO NOT use brake fluid. Contact your local Sealey dealer for details. Purge the system to remove any air.
5.4.
Check your model parts information for spares. Repair kits are also available.
5. MAINTENANCE
Declaration of Conformity
We, the sole importer into the UK, declare that the products listed below are in conformity with the following
EEC standards and directives.
The construction files for these products are held by the Manufacturer
and may be inspected by a national authority on request to Jack Sealey Ltd
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery
Air Hydraulic Press Models
YK30FAH
YK50FAH
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
Signed by Mark Sweetman
Date 25 July 2003
4.1.
INSTALLATION.
4.1.1. Securely attach the press to a flat, firm, level surface taking into account clearance for working pieces.
4.1.2. Purge hydraulic system.
Before operating the press, purge the hydraulic system in order to eliminate any air that may have built up during transit. Open the
release valve and pump the handle several times. Should the system malfunction at any time, repeating this process may resolve the problem.
s
s
s
s
DANGER!
Models are purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always ensure
the workpiece is secured on table and loads that flex will not suddenly give causing danger to operator or damage to component. Also ensure
you have read and understood chapter 1 safety instructions.
4.2.
OPERATING INSTRUCTIONS.
4.2.1. Check that the release valve on the hydraulic unit is fully closed, ready for operation.
4.2.2. Place workpiece onto the work table or the two arbors appropriately positioned. Position the head of the hydraulic unit on the centre
of the workpiece using appropriate extension. Note: care must be taken to ensure an arbor does not fall from the press worktable.
4.2.3. DO NOT exceed the stroke indicated on the label or the red mark on the piston.
4.2.4. DO NOT apply off centre loads.
4.2.5. When work is complete release the pressure and the piston/ram head will retract automatically.
Note:
Always keep the piston, extension screw and pump piston retracted after use.
4. INSTALLATION & OPERATING
3.1.3. For installation see chapter 4.
3.1.4. Once installed, screw the pump handle into the pump arm.
3.1.6. Place v-blocks on work table ready for use. Take care to ensure the v-blocks do not fall from the work table.
IMPORTANT! Ensure that the work table is level and that either end rests upon the appropriate pin before use. Using the press when the table
is not level places excessive strain on the winch cable and main frame and is therefore extremely hazardous.
To level the table, lower using the winch until the lower end of the table rests upon the pin. Now loosen the cable fastening bolt on the
other end of the table (i.e. that end which is not resting on the pin, but still supported by the cable) whilst supporting its weight. Gently
lower the loose end of the table until it rests upon the pin. Now re-tighten the cable fastening bolt on that end.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE MACHINE.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PRODUCT TO US.
Please telephone us on 01284 757500 to obtain the address and phone number of your local agent.
If product is under guarantee please contact your dealer.
De-commissioning Product
Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose
of the product and the oil according to local regulations.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor,
Sealey Group
, Bury St. Edmunds, Suffolk.
01284 757500
01284 703534
Web
www.sealey.co.uk
YK30FAH & YK50FAH - 1 - 250703
6. DECLARATION OF CONFORMITY
