3. SPECIFICATION
Model No: ....................................................... YK309FAH.V2
Air Consumption: ........................................................... 9cfm
Bench or Floor Mounting: ............................................... Floor
Capacity: ................................................................... 30tonne
Lateral Ram Travel: .................................................... 200mm
Maximum Height - Ram to Table: ............................. 1030mm
Minimum Height - Ram to Table: ................................ 150mm
Optional Accessories: ...................... YKSG30 - Safety Guard
Optional Accessories: ........................ YKPP8 - Press Pin Set
Overall Height: ......................................................... 1801mm
Ram Diameter: .......................................................... Ø70mm
Ram Stroke: ............................................................... 150mm
Table Aperture: ........................................................... 164mm
Type: ..................................................................Air/Hydraulic
Working Pressure:................................................ 108-123psi
Working Table Depth: ................................................. 184mm
Working Table Width: ................................................. 695mm
4. ASSEMBLY
Unpack the product and check contents. Should there be any damaged or missing parts contact your supplier immediately.
Take care to ensure safety when moving main frame from packing as the unit is very heavy.
Refer to attached parts list.
Seek assistance from another person on assembly of heavy parts.
Assemble press, if possible, in close proximity to where the press will be located.
4.1.
FRAME ASSEMBLY
4.1.1.
Attach load slings around the top cross member of the frame (#17) and using a suitable hoist or gantry, slowly, and in a controlled
manner lift the frame up and out of the transportation crate, into an upright position.
WARNING!
Take care when lifting the frame not to damage the pre-assembled ram assembly (#14).
4.1.2.
Keep the frame assembly in an upright position, held safely by the load slings.
▲
DANGER!
DO NOT
allow the frame to fall over.
4.2.
ATTACH BASE SECTION
NOTE:
The base section (#10), supports (#9), hex head screw M10 x 25 (#8),
fl
at washer M10 (#7), spring washer M10 (#6) and
nut M10 (#5) are supplied pre-assembled.
4.2.1.
Remove the central
fi
xings only, hex head screw M10 x 25 (#8),
fl
at washer M10 (#7), spring washer M10 (#6) and nut M10 (#5)
from the base section (#10).
4.2.2.
Position the base section (#10) onto the frame (#17) and secure with hex head screw M10 x 25 (#8),
fl
at washer M10 (#7), spring
washer M10 (#6) and nut M10 (#5) loosely.
4.2.3.
Remove the top
fi
xings only, hex head screw M10 x 25 (#8),
fl
at washer M10 (#7), spring washer M10 (#6) and nut M10 (#5) from
one of the supports (#9).
4.2.4.
Position the support (#9) onto the frame (#17) and secure with hex head screw M10 x 25 (#8),
fl
at washer M10 (#7), spring
washer M10 (#6) and nut M10 (#5) loosely.
4.2.5.
Follow section 4.2.4 to attach the other support (#9).
4.2.6.
Repeat sections 4.2.1 to 4.2.5 to attach the other base assembly.
4.2.7.
On
a
fl
at level
fl
oor, level the frame using a good quality spirit level. Fully tighten all
fi
xings.
4.2.8.
Remove the load slings and store them in a safe and secure location.
WARNING!
Take care and seek assistance from another person when lowering and levelling the frame assembly onto the
fl
oor.
4.3.
ATTACH THE PUMP ASSEMBLY
NOTE:
The pump assembly (#32), oil hose (1) (#29), oil hose (2) (#23), air hose (#33), foot pedal (#34), air hose (#35) and quick
coupler (male) (#36) are supplied pre-assembled.
4.3.1.
Transfer the pump assembly (#32) from its transport location by
fi
rstly removing the
fi
xings, hex head screw M10 (#24) and
fl
at
washer M10 (#7). Retain the
fi
xings.
4.3.2.
Attach the pump assembly (#32) into position at the top, right hand side of frame (#17) and secure with the retained
fi
xings.
WARNING!
Seek assistance from another person with this task as the pump assembly is heavy.
4.4.
ATTACH BED FRAME
WARNING!
Seek assistance from another person with this task as the bed frame is heavy.
4.4.1.
Pass the lower bed frame pins (#4) through the holes on the press frame assembly uprights (#17) at the desired height.
4.4.2.
Fit the circlips (#3) to the table support pins.
NOTE:
The circlips should be spaced equidistant from the press frame sides to allow for ease of bed frame assembly (#2).
4.4.3.
Taking
fi
rm hold of the bed frame (#2), tip it into a diagonal position so that it can be introduced between the mainframe uprights,
and then carefully lower it back to a horizontal position to rest on the lower bed frame pins (#4), between the circlips (#3).
WARNING!
Take care not to allow the bed frame to drop onto the bed frame pins and ensure your hands and
fi
ngers are clear of
the bed frame when lowering.
4.4.4.
Pass the upper bed frame pins (#4) through the bed frame (#2) and the press frame assembly uprights (#17).
4.4.5.
Fit the circlips (#3) to the table support pins.
4.4.6.
Place the V-blocks (#1), in the required orientation, onto the bed frame (#2).
4.5.
ATTACH HANDLES
4.5.1.
Fit handle (#11) into handle recess C on pump assembly and secure with
fl
at washer M8 (#38) and hex head screw M8 x 20 (#37).
4.5.2.
Fit handle (#39) into handle recess D on pump assembly and secure with
fl
at washer M8 (#38) and hex head screw M8 x 20(#37).
YK309FAH.V2 Issue 1 15/03/22
Original Language Version
© Jack Sealey Limited
