4. operaTion
warninG!
ensure that you read, understand and apply Section 1 Safety Instructions before using the winch.
warninG!
Before every use thoroughly inspect every part of the winch for signs of damage or stress. If any are found
Do noT
use
but refer to an authorised repair agent for all repairs.
Do noT
use the wire rope if there is any evidence of fraying, stress or other
damage.
Do noT
kink the wire rope.
4.1.
aTTachinG winch To loaD anD anchor
4.1.1.
Pass the anchor pin through the puller body (fig.1). When it is as far as it can go rotate through a further 180° and insert fully home.
A ‘d’ pin (not supplied) may be pushed through the anchor pin to provide additional security.
4.1.2.
Attach the puller to a suitable anchor point, ensuring that it is capable of withstanding the maximum line pull, check any chains, strops
or shackles to ensure they are rated equal to or exceeding the maximum line pull.
Do noT
wrap the wire rope back on itself.
4.2.
inserTinG wire rope.
4.2.1.
Place forward and reverse levers away from the release lever. Push the release lever into the locked position as shown in fig 2.2,
this allows the internal jaws to open, enabling the wire rope to be inserted through the wire feed (fig 2.1).
Note:The release lever can be difficult to lock into place, it requires firm pressure downwards onto it (the forward and reverse
levers will be seen to move out), before also pushing forwards to lock it into place. This is best carried out with the winch tipped up
at an angle (see fig.3)
4.2.2.
Insert the wire rope through the feed (fig 2.1). Direct the wire rope out of the back and run above the anchor pin.
4.2.3.
Take up slack by pulling the cable through the winch. When the slack has been taken up unlock the release lever by pushing down
and back. The winch is now ready for use.
4.3.
pullinG/lifTinG a loaD
4.3.1.
To pull/lift a load, ensure the wire rope is firmly attached to the load to be pulled/lifted and the winch is anchored to a suitable
position.
4.3.2.
Lock the handle onto the forward lever (fig 2.4) by locating the pin and twisting through 180°.
4.3.3.
moving the handle back and forth will pull the wire rope through the winch.
noTe:
As an added safety feature the forward lever is fitted with a shear pin. If the load is greater than the capacity of the puller the
pin will shear. The pin will require replacing with part no. WRP1600.16 or WRP3200.16.
4.4.
lowering a load
4.4.1.
To lower a load, lock the handle onto the reverse lever
(fig 2.3)
, by locating the pin and twisting through 180°.
4.4.2.
moving the handle back and forth will push the wire rope back through the winch.
4.4.3.
When all the load has been removed from the winch, move the release lever back into the locked position (see 4.2.1.above) and
withdraw the wire rope from the winch.
4.4.4.
Wind the wire rope back onto its reel, take this opportunity to inspect the rope for any damage that may have occurred during the
pulling procedure. Unlock the release lever on the winch, if not being used, store away in a safe, dry, childproof location
5. MainTenance
5.1.
Clean the puller after each use and wipe with a slightly oiled cloth. Store in a safe, dry, childproof location.
sealey Group, Kempson way, suffolk Business park, Bury st edmunds, suffolk. ip32 7ar
01284 757500
01284 703534
www.sealey.co.uk
environMenT proTecTion
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important
: no liability is accepted for incorrect use of this product.
warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
WRP1600, WRP3200 | Issue 3 01/03/18
Original Language Version
© Jack Sealey limited
fig.1
fig.2
fig.3
