IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
Refer to Instruction
Manual
1. SAFETY
VS703.V6 Issue: 1 - 16/03/17
Original Language Version
© Jack Sealey Limited
Wear Eye
Protection
INSTRUCTIONS FOR:
BEARING RACE & SEAL DRIVER SET -
10 PIECE
MODEL NO:
VS703.V6
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
WARNING!
Always wear approved eye protection when using the driver. Failure to do so may result in serious injury.
Normal spectacles are
not adequate protection.
Familiarise yourself with the specific applications and limitations of the driver, as well as any potential hazards.
If unsure of the applications or limitations of the driver, contact your supplier.
Ensure that the driver is the correct tool for the task.
DO NOT
use the driver
for any purpose other than that for which it is designed.
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Ensure that the workpiece is stable and that there is adequate lighting.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Use the correct size and type of hammer for the task. The recommended diameter of hammer face is 10mm larger than tool head.
Check that the hammer shaft is in good order and is firmly secured in the hammer head. Note that for seal installation a soft-faced hammer
should be adequate and will be less likely to damage the tool.
Make sure that the face of the hammer and the head of the tool are clean and free from grease, oil, etc.
Position the tool so that it is struck away from your body.
Strike the driver squarely on the head -
DO NOT
hit the tool off centre, or at an angle (fig.1).
DO NOT
use the driver if it is bent, chipped, has a mushroom head, or is otherwise damaged (fig.2).
DO NOT
strike the side of the driver body (fig.3).
DO NOT
use driver if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT
use the driver
when you are tired or under the influence of alcohol, drugs or intoxicating medication.
Keep children and unauthorised persons away from the working area.
When not in use, pack into the case, and store in a safe, dry, childproof location.
Set of nine aluminium bearing and seal drivers. Suitable for straight installation of bearing race without damage to the bearing or axle housing.
Fits most popular bearing race sizes.
2. INTRODUCTION
3. SPECIFICATION
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VS703
Driver Sizes: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø39.5, 44, 50, 59, 63, 64.5, 72, 76, 81mm
VS703.V6-1 . . . . . . . . . . . . . . . . . . . ..Bearing Adaptor 39.5mm
VS703.V6-2 . . . . . . . . . . . . . . . . . . . . . .Bearing Adaptor 44mm
VS703.V6-3 . . . . . . . . . . . . . . . . . . . . . .Bearing Adaptor 50mm
VS703.V6-4 . . . . . . . . . . . . . . . . . . . . . .Bearing Adaptor 59mm
VS703.V6-5 . . . . . . . . . . . . . . . . . . . . . .Bearing Adaptor 63mm
VS703.V6-6 . . . . . . . . . . . . . . . . . . . ..Bearing Adaptor 64.5mm
VS703.V6-7 . . . . . . . . . . . . . . . . . . . . . .Bearing Adaptor 72mm
VS703.V6-8 . . . . . . . . . . . . . . . . . . . . . .Bearing Adaptor 76mm
VS703.V6-9 . . . . . . . . . . . . . . . . . . . . . . . ..Blow Moulded Case
VS703.V6-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handle
VS703.V6-11 . . . . . . . . . . . . . . . . . . . . .Bearing Adaptor 81mm
4. CONTENTS
