Fig.2
Fig.3
NOTE: Before installing the new bush/bearing refer to the vehicle manufacturer's service instructions, or a proprietary manual, to
establish the correct horizontal alignment or positioning of the bush. Mark where the old bush sits to ensure correct replacement.
IMPORTANT!
Ensure the area around the bush is thoroughly cleaned.
4.1.
Bush/Bearing Removal (See fig.2)
4.1.1 Choose the thickest threaded bar that will pass through the bearing/bush.
4.1.2 Lubricate the force screw and nuts with a high quality molybdenum disulphide grease.
4.1.3 Choose the correct size of adapter to locate on the external casing of the bearing/bush. This adapter must be able to pass through the
suspension arm.
4.1.4 Choose the correct size of adapter to sit square on the bearing/bush housing on the suspension arm. This must be large enough to accept
the bush as it is pushed out.
4.1.5 Insert the force screw through the bearing/bush and locate the adapters as described in 4.1.3 and 4.1.4. Attach the washers and nuts at
each end of the force screw. Refer to fig.2.
4.1.6 Make sure the U shaped viewing slots are aligned so that you can see the bush being removed.
4.1.7 Make sure the adapters and force screws are correctly positioned before tightening the nuts.
4.1.8
Using the correct sized ring spanner,
gradually tighten the force screw nuts to drive the bearing/bush from its housing.
DO NOT
use air tools.
DO NOT
exceed the maximum torque rating of each force screw as listed in fig.3.
4.1.9 Unscrew the nuts to separate the adapters and retrieve the bearing/bush.
350mm long
Force Screw
(5-pieces)
Sizes/Torque*
M10X1.5/ 33Nm
M12X1.5/ 60Nm
M14X1.5/ 99Nm
M16X1.5/155Nm
M18X1.5/170Nm
*
Max recommended
torque (lubricated).
4.2.
Bush/Bearing Installation (Fig.2)
4.2.1 Fitting is the reverse of the removal proceedure.
4.2.2 Before installing the new bearing/bush, clean the inside of the housing with abrasive cloth to ensure it is free of debris and corrosion.
4.2.3 Lightly oil the outer ring of the bearing/bush and using a hammer gently tap the outer ring of the bearing/bush to locate it in the housing.
4.2.4 Use the largest force screw that will fit through the centre of the bearing/bush and clean and lubricate its threads.
4.2.5 Select the appropriate sized adapters (see Section 4.1) assemble them and the force screws (see fig.2). Once the adapters are square on
the housing and on the bearing/bush outer ring, tighten the nuts to force the bearing/bush into the suspension arm. Make sure that the
bearing/bush is square to the housing during installation.
4.2.6 Once the bearing/bush is installed, remove, clean and lubricate the components and return to their case.
4.3. Using with a workshop press
4.3.1 Where in-situ access isn't possible, the adapters can be used with a standard work shop press for bush/bearing removal and installation.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
4. OPERATION
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
VS7026.V2 Issue No.1 - 02/02/15
Original Language Version
© Jack Sealey Limited
Содержание VS7026.V2
Страница 3: ......
