3. CONTENTS AND SPECIFICATION
6. USING A CARTRIDGE FILTER
4. ASSEMBLY
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VMA914
Motor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1300W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V
Drum Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30ltr
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10kg
Replacement Foam Filters: (Pack of 10) . . . . . . . . . . . . PC200FF10
Replacement Cartridge Filter: . . . . . . . . . . . . . . . . . . . . . . PC310CF
ITEM DESCRIPTION
1
Main switch.
2
Mode selection buttons
3
Detergent pipe coupling.
4
Suction hose inlet.
5
Detergent tank
connecting hose.
6
Detergent tank.
7
Drainage outlet.
8
Cartridge filter and lid.
9
Foam filter.
10
Nozzle.
ITEM DESCRIPTION
11
Hand held lance.
12
Stainless steel extension
tube.
13
Suction hose.
14
Crevice tool.
15
Round brush.
16
Combination floor brush.
17
Carpet lance.
18
Top section
19
Main drum
4.1
Do not connect the mains plug yet.
4.2
Undo main drum clasps and lift off the top section (18).
4.3
Remove contents from inside the tank. Check and identify
each component as listed in fig.1. If anything is missing or
damaged please contact your supplier immediately.
4.4a
Insert a large wheel on each side of the rear basket and
ensure they are pushed all the way in.
4.4b
Turn the main drum (19) upside down and insert the moulded
castor mountings into their positions in the black base until
they lock into position.
4.5a
For dry suction fit the cartridge filter (8).
4.5b
For carpet washing or wet suction fit the foam filter (9).
4.6
Re-assemble the top section (18) to the main drum (19).
4.7
Fasten the 2 clasps.
4.8
Attach the suction hose (13) to the suction inlet (4) on the front
of the main drum.
4.9
Twist and lock the end of the suction hose (13) into the nozzle
(10). Push the end of the nozzle (10) into the stainless steel
extension tube (12). Fit the required accessory to the base of
the stainless steel extension tube (12) or directly to the nozzle
(10) if the stainless steel extension tube (12) is not required.
WARNING!
Always disconnect the plug from the mains supply
before removing the top section (18).
6.1
IMPORTANT:
The filter is made of high quality paper designed
to filter small particles of dust.
We recommend that this filter
be used for dry vacuuming only.
6.1.1 The cartridge filter (8) must be completely dry when used to
collect dry dust as a wet or damp filter will clog quickly and be
very difficult to clean.
6.1.2 Check the cartridge filter (8) carefully and regularly for tears or
small holes. Even a small hole can cause dust to be exhausted.
Never use a cartridge filter with holes or tears as this may
cause damage to the motor and invalidate warranty. Replace it
immediately.
6.2 INSTALLING & CLEANING
6.2.1 Slide cartridge filter (8) down over filter cage on the top section
(18).
6.2.2 Apply gentle pressure to the cartridge filter until it is fully located
over the filter cage. Place the lid over the end of the cartridge
filter, ensuring that the locking device on the lid locates into the
hole in the filter cage. Turn the locking device on the lid
clockwise until the lid and filter are locked on to the filter cage.
6.2.3 To remove cartridge filter for cleaning, turn the locking device on
the lid anti-clockwise to unlock the filter. Remove the lid, hold
the base of the filter and gently pull it off the cage.
6.2.4 Clean the filter by tapping it on the inside of a waste bin.
fig.1
High powered unit ideal for cleaning carpets, car interiors, fabrics and
upholstery. Supplied with carpet lance, hand held lance, full wet and
dry vacuum accessory kit including stainless steel rigid extension
tube, cartridge filter and foam filter. Large capacity drum with external
detergent tank for easy filling. Features remote operation controls on
nozzle enabling switiching between vacuum and detergent modes
uninterrupted. Fitted with two fixed wheels and two castors and cable
storage hook.
2. INTRODUCTION
Original Language Version
VMA914 Issue: 1 - 06/07/11
5. PROGRAMMING REMOTE CONTROL
5.1
Ensure the machine is plugged into the power supply with the
power on.
5.2
Set the main switch (1) to the ('I') position.
5.3
Locate the detergent mode selection button (2) on the top
section (18) indicated by the symbol.
5.4
Press and hold the detergent mode button until the indicator
light above the mode selection buttons (2) illuminates.
5.5
With the light still illuminated, press and hold the detergent
mode button on the nozzle (10).
5.6
When the light starts to flash the nozzle (10) is programmed to
the machine. You should now be able to operate the detergent
and vacuum modes using the nozzle (10).
5.7
If the light does not flash go back to step 5.4 and start again.
