Motor . . . . . . . . . . . . . . . . . . . . . . . . .230V - 1500W
Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . .4500rpm
Saw blade . . . . . . . . . . . . . . .Ø250 x Ø30 x 3.2mm
Max depth of 90
O
cut . . . . . . . . . . . . . . . . . . .70mm
Max depth of 45
O
cut . . . . . . . . . . . . . . . . . . .55mm
Table . . . . . . . . . . . . . . . . . . . . . . . . . . .625 x 463mm
Dust extraction port Ø (taper) . . . . . . . . . . .30 - 34mm
Sound power . . . . . . . . . . . . . . . . . . . . . . .114.6dB(A)
Sound pressure . . . . . . . . . . . . . . . . . . . . . 105.0dB(A)
3. SPECIFICATION
4. ASSEMBLY
5. ADJUSTMENTS
p
WARNING! ENSURE THAT THE SAW IS NOT CONNECTED TO THE MAINS POWER BEFORE COMMENCING ASSEMBLY.
4.1.
Saw stand or bench
The saw must be mounted either on the Sealey purpose designed stand, model number TS10CZ/ST, or a sturdy workbench.
Ensure that the supporting surface is strong enough to take the weight of the saw and any workpiece. Position the saw in a suitable work area
with enough clearance to allow room when working with large workpieces. Table extensions are available, Sealey model number TS10CZ/EWS,
to cater for large workpieces. Ensure that there is adequate lighting and that the saw blade can be clearly seen.
4.2.
Blade guard
4.2.1. Loosen the wing nut on the blade guard (fig. 2.1).
4.2.2. Place the blade guard on the splitter (fig. 1.5) so that the screw fits into the slot in the splitter.
4.2.3. Slide the blade guard forward and tighten the wing nut.
4.3.
Extraction
4.3.1. Fit extraction T piece (fig. 2.3) into extraction port and connect pipe (fig. 2.4) to blade guard.
4.3.2. Connect the T piece outlet (fig. 2.2) to a suitable extraction system.
p
WARNING!
Wood dust can be harmful to health by inhalation and skin contact and concentrations of small dust particles in the air can
form an explosive mixture. Therefore, ensure that there is adequate ventilation and that the saw is attached to a dust-extraction unit.
fig. 2
p
WARNING! ENSURE THAT THE SAW IS NOT CONNECTED TO THE MAINS POWER BEFORE MAKING ANY ADJUSTMENTS.
5.1.
Cutting depth
5.1.1. Adjust cutting depth by turning the handwheel (fig. 1.8) - anticlockwise to increase depth, clockwise to decrease.
5.2.
Angle of cut
5.2.1. Set the blade for maximum depth - see 5.1.
5.2.2. Loosen the locking handle (fig. 1.9) and move the handwheel (fig. 1.8) until the pointer aligns with the required angle on the scale.
5.2.3.
Firmly tighten locking handle.
Initial set-up -
before first use set blade angle to 0
O
on scale and confirm, using a square, that the blade is at 90
O
to the table. If it is not, loosen
locking handle and adjust stop screw (fig. 3.A) to give 90
O
. Similarly, set the blade at 45
O
on the scale and check that the blade
to table angle is 45
O
. Any required adjustment is provided by stop screw (fig. 3.B).
5.3.
Splitter
5.3.1. Set blade to maximum cutting depth at 90
O
to the table (see paras. 5.1. & 5.2.).
5.3.2. Remove the blade guard (para.4.2.) and the table insert (para. 5.7.).
5.3.3. Loosen the two socket head screws clamping the splitter.
5.3.4. Adjust the splitter so that the top of it is 80mm above the table and the splitter-to-blade gap is 3 - 5mm.
5.3.5. Retighten the two clamping screws.
Note: If the saw is to be use for covered cuts (cutting a groove in the wood) then the splitter must be set so that the top of it is 2mm below the
tip of the topmost blade tooth. Remember to reset splitter and replace blade guard when reverting to through cutting.
5.4.
Cross stop (Mitre gauge)
For straight cross-cutting set the blade at 90
0
to the table. The mitre gauge is used to cut a workpiece at an angle to the blade. To do so
position the cross stop in either the right or left hand channel and set the mitre to the required angle for cutting.
s
CAUTION!
If you are bevel cross cutting (
i.e.blade is tilted
) ensure you place cross stop in the
right-hand
table slot only. This will ensure
that the blade is tilted away from the cross stop and your hands.
TS10CZ - 0016 - (1) - 040501
3.1.
Specification
fig. 3
