4. priminG & OperatiOn
5. maintenanCe
4.1 PrImInG of tHe unIt
WarninG! neVer run the pump in an unprimed condition as this will damage the pump and invalidate your warranty.
4.1.1 Before the pump can be used for the first time it must be primed with fuel using the procedure outlined below.
4.1.2 Place the nozzle into an appropriate collecting container and press and hold the trigger.
4.1.3 operate the manual priming lever until fuel emerges from the nozzle. release the trigger.
4.1.4 the pump is now ready to be switched on.
4.1.5
If the pump is moved from one container to another it must be reprimed before it can be used again.
4.2 normAl oPerAtIon
4.2.1 switch on the pump and remove the filler cap from the container or vehicle tank that is to be filled.
4.2.2 Place the nozzle into the tank opening.
4.2.3 Press and hold the trigger until the desired amount of fuel has been dispensed.
4.2.4 release the trigger, remove the nozzle from the tank and replace the filler cap.
4.2.5 ensure that the delivery nozzle and hose are safely stowed adjacent to the pump ready for the next delivery.
danGer!
clean up any spillage in accordance with regulations governing the handling of diesel fuels.
WarninG!
do not operate the pump unsupervised.
WarninG!
do not allow the pump to run dry. At the end of each delivery the suction filter should always be below the level of the fuel.
WarninG!
do not let the pump deliver for more than 5 minutes against a closed nozzle in order to avoid exceeding the permitted
operating temperature.
WarninG!
regularly check the delivery hose and connections for damage in order to avoid leakage of fuel.
4.3 emerGencY oPerAtIon
4.3.1 In the event of a power failure it is possible to manually pump very small quantities of fuel using the procedure outlined below.
4.3.2 Place the nozzle into the container or vehicle tank and press and hold the trigger.
4.3.3 operate the manual priming lever to deliver the fuel.
4.3.4 When the delivery is complete release the trigger and remove the nozzle.
4.3.5 safely stow the delivery tube and nozzle and replace the filler cap on the container or vehicle tank.
4.4 demountInG And remountInG tHe PumP
4.4.1 When demounting the pump in order to place it onto another container or for storage observe the following procedure.
4.4.2 take suitable precautions to clear up minor spills of fuel that may occur when demounting the pump.
4.4.3 switch the pump off and disconnect it from the battery or unplug it from the mains power supply.
4.4.4 Before the pump can be unscrewed from the fuel container the delivery hose must be disconnected.
4.4.5 to empty the fuel remaining in the delivery hose firstly place the nozzle into a collection container and hold the trigger open.
4.4.6 Keeping the trigger open begin to loosen the union where the hose is connected to the pump. As the union becomes loose and air
enters the pipe the excess fuel should flow into the container. Keep the disconnected end of the hose at a high level and the container
at a low level so that all the fuel is emptied from the hose.
4.4.7 unscrew the pump from the threaded connector on the fuel container and slowly remove the pump with the suction hose and filter
attached allowing the fuel to run out completely.
4.4.8 If the pump is then mounted to another fuel storage container it must be primed first before switching on.
4.4.9 If the pump is to be stored even for a short period of time the pump and its hoses should be laid into a clean oil tray in order for all
excess fuel to drain out. the pump and hoses should be cleaned and stored in a well ventilated store suitable for product that handles
fuel.
5.1
the pump has been designed for low maintenance. should any problems occur return the unit to your local sealey dealer.
5.2
clean the entire installation and inspect all piping connections for leaks. rectify any damage immediately.
5.3
Inspect the filter at the end of the suction tube every time the tank is refilled.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
impOrtant:
no liability is accepted for incorrect use of this product.
WarrantY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
infOrmatiOn:
for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
sole uK distributor, sealey Group,
Kempson Way, suffolk Business Park
,
Bury st. edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
Original Language Version
tP97, tP9724, tP97230 Issue: 3 - 22/03/10
