3.1.
EYESHIELD ASSEMBLY
3.1.1. Remove protective film from eyeshields, place support plate on top and assemble as in figure 1.
3.1.2. Assemble shield arms as in figure 2. One connects to the right hand side of grinder and the other to the left.
3.1.3. Securely attached each eyeshield to the grinding stone guard as in figure 4 A.
3.1.4. Set the clearance between the stone and the eyeshield at 5mm (fig 3).
3.2.
TOOLREST ASSEMBLY
3.2.1. Bolt each tool rest to the bottom of the stone guard as in figure 4. B.
3.2.2. Set the clearance between the stone and the toolrest at 2mm (fig 3).
2. TECHNICAL SPECIFICATIONS
Model: SM53
Dry Grinding stone dims . . . .150 x 25 x 20mm
Dry grinding stone part no . . .SM53-5/GW150C (Course)
. . . . . . . . . . . . . . . . . . . . . . .SM53-5/GW150F (Fine)
Dry Grinding Speed . . . . . . . . . . . . .2850 RPM
Wire Brush dims . . . . . . . . . . . .150x16x12mm
Wire Brush part no . . . . . . . . . .SM53-5/WB125
Buffing Mop . . . . . . . . . . . . .125 x 16 x 12 mm
Buffing Mop part no . . . . . . . . .SM53-5/BM125
Motor . . . . . . . . . . . . . . . . . .1/2 Hp - 230V/1ph
Model: SM54
Dry Grinding stone dims . . . .200 x 25 x 20mm
Dry grinding stone part no . . .SM54-6/GW200C (Course)
. . . . . . . . . . . . . . . . . . . . . . .SM54-6/GW200F (Fine)
Dry Grinding Speed . . . . . . . . . . . . .2850 RPM
Wire Brush dims . . . . . . . . . . . .200x16x12mm
Wire Brush part no . . . . . . . . . .SM54-6/WB175
Buffing Mop . . . . . . . . . . . . .175 x 19 x 12 mm
Buffing Mop part no . . . . . . . . .SM54-6/BM175
Motor . . . . . . . . . . . . . . . . . .3/4 Hp - 230V/1ph
3. ASSEMBLY & ADJUSTMENT
Unpack the product and check contents, should there be any damaged or missing parts contact your supplier immediately.
p
WARNING!
Before use, the machine must be bolted to a stable, fireproof bench or table. Strong enough to take the weight of the
machine and the workpiece. Failure to comply with this instruction could result in damage or severe personal injury.
fig 1
fig 2
fig 3
fig 5
fig 4
7
DO NOT allow the workpiece to become jammed between the stone and eyeshield or tool rest.
7
DO NOT get the
grinder
wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT use grinder where there is flammable liquids, solids or gases such as paint solvents, including waste wiping or cleaning rags etc.
7
DO NOT touch the workpiece close to the ground surface as it will be very hot. Allow to cool. The workpiece may also be very sharp.
7
DO NOT operate the
grinder
when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT leave the
grinder
operating whilst unattended.
3
When not in use switch the
grinder
off, and disconnect from the mains power supply, and clean the machine and working area.
3.3.
BRUSH OR BUFFER ATTACHMENT.
3.3.1. Hold grinding stone firmly. To protect your hands use a cloth or wear
gloves. Remove the thread cap from the grinding stone spindle
and screw on the adaptor arm (fig 5.1.).
3.3.2. Install flange (2), install the brush or buffer (3) and hold the second
flange (4) against (3) and lock with nut (5). Ensure washers are
installed with the flange on the outside, (i.e. the concave side
against the blotter).
4.1. MANDATORY SAFETY INSTRUCTIONS. (The following instructions must be observed together with chapter 1 safety).
s
DANGER! use of a damaged stone is dangerous and may cause damage or personal injury.
p
WARNING! Ensure grinder is unplugged from the mains power supply before attempting to change grinding stones (or wheel).
3
Only persons qualified under the Abrasive Wheels Regulations and holding a current grinding wheel certificate are authorised
to change and dress grinding stones (wheels).
3
Grinding stones (wheels) used with the machine must be of an adequate speed rating and suitable for the material to be ground.
3
Ensure the cutting stones maximum speed specification is higher than that indicated on the machine data plate.
3
Check grinding stones are secure, and the stone is not worn or damaged, that there are no fissures or cracks. if damaged replace immediately.
3
Ensure replacement stone is not damaged in any way such as cracks, deformations or splinters etc. Also check the mounting flanges
to ensure they are not deformed, burred or chipped. Damaged flanges must
NOT
be used as they may cause irregular pressure on the stone
4. GRINDING STONES
SM53, SM54 - 0016 - (1) - 010200