background image

  5.  CHANGING CUTTING BLADE

  

DANGER! The use of damaged blades is dangerous and may cause injury.

  

WARNING! Ensure that the cut-off machine is unplugged from the power supply before attempting to change the cutting blade.

5.1 IMPORTANT! 

Cutting blades used with this machine shall be of an adequate speed rating and suitable for the task in hand.

 

Order from your dealer quoting model no. SM355B.98  

5.1.1  Before using a cutting blade ensure that there are no fissures or cracks in it. Once  mounted on the cut-off machine, test the blade before  

 

use by facing the cut-off machine in a safe direction (turned away from yourself, others and vulnerable  items) and run it for a short time. 

5.2. 

REMOVING AND INSTALLING CUTTING BLADES (Refer to figs. 5 & 6)

NOTE: 

Removing and installing blades is only to be undertaken by competant persons.

5.2.1  Lift the arm into the up position. 

5.2.2  Loosen the two hex screws to allow the blade access cover to be moved to the right and removed.

5.2.3  Pull the blade catch down and to the right and turn the blade using a 8mm hex key until the catch engages and prevents the blade from turning.

5.2.4  Keep the blade catch engaged and undo the blade hex screw anticlockwise.

5.2.5  Push back the blade guard and undo the hex screw to remove the blade, take care to note the orientation and position of the flanges and    

 

washers. Fit the new blade, assembly is the reverse of the above instructions. 

 

NOTE: 

Take care to not overtighten the blade hex screw.

 6.  MAINTENANCE

 

WARNING! Ensure that the cut-off machine is unplugged from the power supply before attempting any maintenance.

6.1

 

Regularly clean the dust which accumulates inside the protective guard and on the external parts.

6.2

 

Periodically clean and oil the vice screw.

6.3

 

Change the cutting blade when it is worn and/or does not operate efficiently.

6.4

 

Before each use, check for obvious signs of damage to the machine. Also check for loose screws and other moving parts, incorrectly   

 

mounted or misaligned parts and any other factors that might create an unsafe working environment.  

 

WARNING! 

Should excessive noise or vibration occur, cease use immediately. Turn off machine and disconnect from power supply. Do  

 

not use the machine again until the problem has been fully resolved.

6.5. 

CHANGING THE MOTOR BRUSHES.

 

The motor brushes should be checked periodically for wear and renewed when worn down or pitted. The brushes can be accessed either  

 

side of the motor casing as seen in fig.7. 

6.5.1  Unscrew the plastic covers and withdraw the brush assemblies for inspection.

6.5.2  Insert the new brush into the keyway. Place the plastic cap over the head of the brush assembly and press the spring downwards 

 

ensuring that the tabs on either side of the brush head enter the same keyway as  the brush. Screw the caps back into position.

Fig.5

Fig.6

Fig.7

01284 757500

01284 703534

[email protected]

Sole UK Distributor, Sealey Group,

Kempston Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk, IP32 7AR

www.sealey.co.uk

W e b

email

NOTE: 

It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: 

No liability is accepted for incorrect use of this product. 

WARRANTY: 

Guarantee is 12 months from purchase date, proof of which will be required for any claim. 

INFORMATION: 

For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

 

  

Environmental Protection.

  

Recycle unwanted materials instead of disposing of them as  

   

waste. All tools, accessories and packaging should be sorted,  

   

taken to a recycle centre and disposed of in a manner which  

   

is compatible with the environment.

  

WEEE Regulations.

  

Dispose of this product at the end of its working life in compliance   

   

with the EU Directive on Waste Electrical and Electronic Equipment.  

   

When the product is no longer required, it must be disposed of in an  

   

environmentally protective way. Contact your local solid waste  

 

   

authority for recycling information.

Original Language Version

© Jack Sealey Limited

Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to 

www.sealey.co.uk, email [email protected] or phone 01284 757500.

SM355B    Issue: 4(I) 25/02/14     

Содержание SM355B

Страница 1: ...ual Current Device RCD is used It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by an RCCB If in any doubt consult a qualified electrician You may obtain a Residual Current Device by contacting your Sealey dealer You must also read and understand the following instructions concerning electrical safety 1 1 1 The Electricity at W...

Страница 2: ...se failure and or personal injury DO NOT remove the safety guard whilst the cut off machine is in use DO NOT attempt to remove a workpiece until the blade has stopped rotating DO NOT touch the workpiece close to the cut as it will be very hot Allow to cool The cut edge of the workpiece will also be very sharp DO NOT leave the cut off machine operating unattended DO NOT operate the cut off machine ...

Страница 3: ...l functions correctly 4 4 MITRE CUTTING 4 4 1 To cut at an angle loosen the vice backstop locking handle by turning it anticlockwise Lift the handle vertically and turn it clockwise to loosen the nut underneath if required Align to the desired angle using the graduated scale on the base plate shown in fig 4 and retighten the vice backstop locking handle Place the workpiece against the backstop and...

Страница 4: ...nsafe working environment WARNING Should excessive noise or vibration occur cease use immediately Turn off machine and disconnect from power supply Do not use the machine again until the problem has been fully resolved 6 5 Changing the motor brushes The motor brushes should be checked periodically for wear and renewed when worn down or pitted The brushes can be accessed either side of the motor ca...

Отзывы: