DISC SANDER 305MM
model no:
SM31.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAfETy
1.1.
ELECTRICAL SAfETy
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information,
it is important that the following information is read and understood.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power
supply.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure
that they are secure.
Important
: ensure that the voltage rating on the appliance suits the power supply to be used and that the
plug is fitted with the correct fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is
replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2
GENERAL SAfETy
9
Familiarise yourself with the product’s application and limitations, as well as the specific potential hazards peculiar to the machine.
WARNING!
ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to.
WARNING!
disconnect from the mains power supply before changing accessories, servicing or performing any maintenance.
WARNING! DO NOT
sand any materials containing asbestos.
WARNING!
Wear approved safety eye / face protection. If dust is generated respiratory protection must be worn.
9
maintain the sander and keep in good condition (use an authorised service agent).
9
Check the alignment of moving parts regularly, for safest performance keep the sander clean at all times.
9
Use the correct type and size of sanding disc for this sander.
9
Before each use check sanding disc for condition. If worn or damaged replace immediately.
9
Replace or repair damaged parts. Use genuine parts only. Non-authorised parts are dangerous and will invalidate the warranty.
9
locate the sander in a suitable area, keep area clean, uncluttered and ensure there is adequate lighting.
9
The sander is for indoor use only.
DO NOT
get the sander wet or use in a damp location.
9
ensure the sander is situated on a solid work surface, adequate for supporting the weight of both the sander and the workpiece.
9
ensure there are no flammable or combustible materials near the work area.
9
Remove ill fitting clothing, ties and loose jewellery, and tie back long hair.
9
Maintain correct balance and footing, ensure the floor is not slippery and wear non-slip rubber soled footwear.
9
Keep hands and body clear of the worktable when operating the sander.
9
ensure there are no nails, screws etc. protruding from the surface to be sanded.
8
DO NOT
operate the sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
leave the sander running unattended.
9
Hold workpiece firmly, avoiding hand positions where a slip may cause your hand to come into contact with the sanding disc.
8
DO NOT
modify or change the sander motor for one with a different rating.
8
DO NOT
turn the sander on until work table is clear of all objects, wood scraps etc.
Recommended fuse rating
13 Amp
S
M31.V3 | Issue: 4 (3) 13/11/18
Original Language Version
© Jack Sealey limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear a mask
Indoor use only
