The SM25 is a bench or stand mounted drilling/milling machine with a 12 speed reversible drive giving flexibility to handle most materials. The
table has a large surface area with inverted ‘T’ slots facilitating the securing of large and awkward shaped work pieces. The machine is supplied
with metric graduated compound scales. Complies with Machinery Directive 98/37/EC and is fully CE approved. A 52 piece clamping kit is
available as an optional extra, Model No.SM25/52T. The machine is supplied with 63mm face cutter, 90mm angle vice, 16mm drill chuck and
safety guard. A stand is available as an optional extra, Model No. SM25/STAND.
2. INTRODUCTION & SPECIFICATION
Drilling capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . .25mm
Swing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496mm
Face Mill capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 63mm
End Mill capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm
Diameter of spindle sleeve . . . . . . . . . . . . . . . . . . . 85mm
Head swivel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
O
Forward/Backward table travel: . . . . . . . . . . . . . . . .145mm
Right/Left table travel . . . . . . . . . . . . . . . . . . . . . . . 370mm
Table working area . . . . . . . . . . . . . . . . . . . .585 x 190mm
Spindle nose taper . . . . . . . . . . . . . . . . . . . . . . . . . . .MT3
Spindle travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92mm
Number of speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Speed range . . . . . . . . . . . . . . . . . . . . . . . . .100-2150rpm
Max. distance spindle to table . . . . . . . . . . . . . . . . .380mm
Max. distance spindle to base . . . . . . . . . . . . . . . . .480mm
Column diameter . . . . . . . . . . . . . . . . . . . . . . . . . . .92mm
Motor power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .750W
Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V 50Hz 6.5A
Overall height . . . . . . . . . . . . . . . . . . . . . . . . . . . . .930mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167kg
Optional stand. . . . . . . . . . . . . . . . . . . . . . . .SM25/STAND
Specification:
!
WARNING!
DO NOT switch the drilling/milling machine on whilst the drill or cutting tool is in contact with the workpiece. Bring the drill or
cutting tool gradually to the workpiece. Avoid un-intentional starting of the drilling/milling machine.
$
DO NOT use the drilling/milling machine for a task it is not designed to perform.
$
DO NOT allow untrained persons to operate the drilling/milling machine.
$
DO NOT get the drilling/milling machine wet or use in damp or wet locations or areas where there is condensation.
!
WARNING!
DO NOT use drilling/milling machine where there are flammable liquids, solids or gases such as petrol, paint solvents, waste
wiping rags etc.
$
DO NOT operate the drilling/milling machine if any parts are missing or damaged as this may cause failure and/or possible personal injury.
$
DO NOT remove the safety guard whilst in use.
$
DO NOT attempt to remove a workpiece until the drill or cutting tool has stopped rotating.
$
DO NOT touch the workpiece close to the cut as it will be very hot. Allow to cool.
$
DO NOT leave the drill or cutting tool operating unattended.
$
DO NOT operate the drill or cutting tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
"
When not in use switch the drilling/milling machine off and isolate from the power supply.
!
WARNING! For safe
handling and movement use
a fork-lift truck or pallet
truck.
3.1
Unpack the product and
check that all components and
tools are present and
undamaged. If any problem is
noted contact your supplier
immediately.
3.2
The machine has been
coated with heavy grease to
protect it in shipping. Remove
the coating with commercial
degreaser, kerosene or similar
solvent before operating. Avoid
getting the solvent on belts or
other rubber parts. After
degreasing coat the machined
surfaces with a medium
consistency machine oil.
fig. 1
!
Contents description:
!
Drilling/milling machine.
!
3 Table handle wheels
(7,11,13)
!
3 Table handles
(7,11,13)
with
integral pivots.
!
3 Handle rods with knobs
(3)
!
1 Punch key
!
1 Hex key (4mm)
!
1 Hex key (5mm)
!
1 Hex key (6mm)
!
1 Milling cutter with MT3 arbor
!
1 Drill chuck and key with MT3 arbor
!
1 MT3 to MT2 conversion arbor
!
1 2-1/2” Angle vice
!
1 Head handle
!
1 Head handle grip with
integral pivot.
3. CONTENTS & ASSEMBLY
SM25.V3 - 1 - 27/03/07
