sl32s | issue 1 27/04/17
Original Language Version
© Jack sealey limited
parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
if the unit sends out buzzer sounds, and the screen shows “WArninG clAmPs reVersed cHecK All connections “. the
polarity is reversed. You need to disconnect the unit and reverse the clamps. correct clamp connections. turn unit back on and
resume operation.
4.8.
using the override Button
warninG! Do not
use override Button unless the jump starter failed to detect vehicle’s battery working voltage.
note:
When vehicle’s battery is completely dead, the jump starter will not detect battery voltage automatically. You will need to
determine the working voltage and “override” the jump start.
4.8.1.
determine the voltage of the battery by referring to the vehicle owner’s manual and make sure that the output voltage of the jump
starter is correct.
4.8.2.
Confirm the correct voltage of electrical system you are going to jump-starting is 12V or 24V.
4.8.3.
turn off the vehicle ignition switch and all accessories (lights, radio, climate control, etc.)
4.8.4.
connect the red Positive Battery clamp to vehicle’s positive battery terminal. then connect the black negative Battery clamp to
the vehicle’s negative battery terminal.
4.8.5.
Press the override Button.
4.8.6.
Press and hold the correct voltage button that matches your vehicle for about 2 seconds.
4.8.7.
screen will show “JumP stArt reAdY”, at the voltage you have chosen.
4.8.8.
crank the engine within 30 seconds.
4.8.9.
if the vehicle does not start after 5 to 8 second, stop and try again.
4.8.10. A
fter the vehicle is started, remove the black Negative Battery Clamp first, then the red Positive Battery Clamp.
4.8.11. recharge the jump starter.
5. trouBleshootinG
Problem
Possible causes
likely solutions
unit beeps and screen shows “outPut
locKed”
Battery clamps are connected backwards
(reverse polarity) or there is a short circuit
disconnect clamps immediately. correct
clamp connections. turn unit back on and
resume operation.
unit failed to jump start vehicle
.
1) Battery clamp cable malfunctions.
2) low battery
3) internal components damaged.
1) repair or replace clamps or cord.
2) recharge the jump starter to full battery
level.
3) check with your local stockist.*service
must be performed only by a qualified
technician.
screen showed ”outPut locKed”and kept
flashing.
You attempted to jump starting for more than
3 times within short time.
the jump starter turned to protection mode in
case of overheating. With for two minutes for
battery to cool. then resume operation.
screen turned to Blank. no message shown
1) usB output or 12V dc output overload or
there is a short circuit. Protection is tripped.
2) low battery
1) Press main Power Button to unlock the unit
and resume operation.
2) recharge the jump starter
sealey Group, kempson way, suffolk Business park, Bury st edmunds, suffolk. ip32 7ar
01284 757500
01284 703534
www.sealey.co.uk
note
: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important
: no liability is accepted for incorrect use of this product.
warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Battery remoVal
t
he battery should be removed from this product by a qualified technician.
under the Waste Batteries and Accumulators regulations 2009, Jack sealey ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
sealey ltd’s Batteries Producer registration number (BPrn) is BPrn00705.
weee reGulations
dispose of this product at the end of its working life in compliance with the eu directive on Waste electrical and electronic equipment
(Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. contact your local solid
waste authority for recycling information.
enVironment protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
