background image

4.1.4.   

Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig 1. 

4.1.5.   

Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be  

 

1/4” internal diameter and fittings must have compatible dimensions.

4.1.6.   

Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.   

4.2.    

Couplings.

 

 

  Vibration may cause failure if a quick change coupling is connected directly to the drill. To overcome this, connect a leader hose to the  

 

  drill (Sealey ref: AH2R or AH2R/38). A quick change coupling may then be used to connect the leader hose to the air line recoil hose.  

 

  See fig.1& fig.2. 

5.  OPERATION

  

 

‰

  

WARNING!

 Ensure you read, understand and apply safety instructions before use.

5.1. 

  

Drill bit fitting. 

Regularly check the drill bit and always change if worn, cracked or otherwise damaged.

 

‰

  

WARNING!

 Unplug from the air supply before placing bit into chuck.

5.1.1. 

  

Open or close the chuck jaws to a point where the opening is slightly larger than the drill or tool bit (fig.4) to be used. Insert the drill bit  

 

into the chuck as far as it will go. Place the chuck key in one of the chuck holes and tighten the chuck securely.

 

‰

 

 

WARNING!

 Ensure you remove the chuck key before starting the drill.       

5.2.    

Connect air supply to drill. Squeeze the trigger to check that the drill is working correctly before starting work. 

 

8

   DO  NOT

 allow drill to run freely for an extended period of time as this will shorten the life of bearings.

5.3.    

Standard drilling instructions. 

 

‰

  

WARNING!

 Ensure you wear approved safety goggles and any other safety items required for the job. Remove the chuck key before  

  using the drill. Also ensure that all other safety requirements are followed.

5.3.1.   

Connect drill to air supply.

5.3.2.   

Ensure the drill is turning in the forward direction by checking that the lever adjacent to the trigger is next to the forward symbol (F). If  

 

not, push the lever over to the forward position (fig.3).

5.3.3. 

  

Hold tool firmly and place the bit tip to the point to be drilled.

5.3.4.   

Depress the trigger to start drill. Move the drill bit into the work piece applying only enough pressure to keep the bit cutting. 

DO NOT  

 

force or apply side pressure to elongate the hole.

5.3.5.   

If the material to be drilled is free standing it should be secured in a vice or with clamps to keep it from turning as the drill bit rotates.

5.3.6.   

When drilling metals, use cutting a light oil on the drill bit to keep it from overheating. Cutting oil will prolong life of bit and improve the  

 

drilling action.

5.3.7.   

For hard smooth surfaces use a centre punch to mark desired hole location. This will prevent bit from slipping as you start to drill.

5.3.8. 

  

A pilot hole may be necessary to assist the final drill size through the work piece. Lock a pilot drill (smaller size drill than the finished  

 

hole size) into the chuck. Follow steps 5.3.1. to 5.3.3. above and drill a pilot hole in the middle of the centre punch mark where final  

 

hole is to be drilled. Insert the final sized bit in chuck. Hold drill firmly, place bit at entrance of the pilot hole and depress the trigger. 

 

‰

   WARNING! 

Be prepared for drill binding on break through. When these situations occur the drill has a tendency to grab and kick in  

  the opposite direction which could cause loss of control. If you are not prepared, this loss of control can result in damage and/or    

  personal injury.

5.3.9.   

If the bit jams in the workpiece or if the drill stalls, release the trigger switch immediately. Remove the bit from the workpiece and   

 

determine the reason for jamming. It may be necessary to reverse the direction of rotation by moving the lever adjacent to the trigger  

 

to the reverse (R) position (fig.3). 

Original Language Version

© Jack Sealey Limited

fig.1

fig.2

“R” reverse

“F” forward

fig.4

fig.3

 S010147         Issue 2 (H, F) 09/05/18

Содержание Siegen Tools S01047

Страница 1: ...ial being drilled 8 8 DO NOT get the drill wet or use in damp or wet locations 8 8 DO NOT apply excessive loads to the drill bit during operation 8 8 DO NOT hold the workpiece by hand Use clamps or a vice to secure the workpiece 8 8 DO NOT use the drill for a task it is not designed to perform 8 8 DO NOT use drill unless you have been instructed in its use by a qualified person 8 8 DO NOT drop thr...

Страница 2: ... is turning in the forward direction by checking that the lever adjacent to the trigger is next to the forward symbol F If not push the lever over to the forward position fig 3 5 3 3 Hold tool firmly and place the bit tip to the point to be drilled 5 3 4 Depress the trigger to start drill Move the drill bit into the work piece applying only enough pressure to keep the bit cutting DO NOT force or a...

Страница 3: ...sk may produce a different average vibration emission We recommend that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task A health and safety assessment by the user or employer will need to be carried out to determine the suitable duration of use for each tool NB Stated Vibration Emission values are type test values and are intended to be typic...

Страница 4: ... the product becomes completely unserviceable and requires disposal drain any fluids if applicable into approved containers and dispose of the product and fluids according to local regulations Note It is our policy to continually improve products and as such we reserve the right to alter data specifications and component parts without prior notice Important No Liability is accepted for incorrect u...

Отзывы: