2. intrOductiOn
Aluminium housing with articulated sanding arm. Features belt tracking control, heavy-duty nose roller and one-handed trigger operation.
Suitable for sanding otherwise inaccessible areas such as around door-shuts. Supplied with three belts. Ideal for the dIY enthusiast and light
garage use. Replacement belts readily available.
3. sPecificAtiOn
Model no: ...................................................................S01046
Belt Size(s): ........................................................ 10 x 330mm
Free Speed: ........................................................... 15700rpm
Air Consumption:............................................................ 7cfm
operating Pressure: ...................................................... 90psi
Inlet Size: ..................................................................1/4”BSP
nett Weight: .................................................................. 0.8kg
noise Power/Pressure: .................................. 90.4/79.4dB(A)
Vibration/Uncertainty: ......................................... 1.1/0.13m/s²
4. PrePArAtiOn fOr use
4.1.
Unpack the product and check contents against the parts listed below. If there is anything damaged or missing contact your supplier
immediately.
Contents: a) S01046.V2 Belt Sander.
b) 4 x Sanding Belt
c) 2 x Hex Key
4.2.
Air supply recommended hook-up is shown in fig.1.
4.2.1.
ensure the sander air valve (or throttle) is in the “off” position before connecting to the air supply.
4.2.2.
You will require an air pressure between 70-90psi, and an air flow of 7cfm.
WArninG!
ensure the air supply is clean and does not exceed 90psi. Too high an air pressure and unclean air will shorten the
product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.2.3.
drain the air tank daily. Water in the air line will damage the sander and will invalidate your warranty.
4.2.4.
Clean air filter weekly.
4.2.5.
line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
4.2.6.
The minimum hose size should be 1/4”. I.d. and fittings must have the same inside dimensions.
4.2.7.
Keep hoses away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.
4.3.
couplings.
Vibration may cause failure if a quick change coupling is connected directly to the air sander. To overcome this, connect a leader
hose to the sander. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See figs.1 & 2.
4.4.
belt Preparation
To ensure full flexibility, and to prolong working life, the belt must be “bedded in”, ref (4.5.2).
4.4.1.
Fit new belt ensuring the direction of travel is correct, and the belt join is
nOt
on the nose roller.
4.5.
tension belt.
4.5.1.
operate the tool without a load applied at half speed for around 10 seconds, then increase to full speed for a further 10 seconds.
4.5.2.
Finally, at a slow operating speed, using a piece of scrap material, apply light pressure to the belt where it runs over the “shoe”.
Increase the operating speed steadily to maximum for a few seconds, then stop.
5. OPerAtiOn
WArninG!
ensure that you have read and understood the safety instructions in Section 1.
5.1.
loosening clamp bolt (fig.3.1. on the top of sander) allows the angle between the grip and the belt to be altered to suit the job in
hand. After adjustment tighten the clamp bolt.
5.2.
once connected to the air supply the sander is started by squeezing the trigger (7).
6. remOVe And rePlAce belt
6.1.
To remove and replace the sanding belt push the idle pulley (4) towards the drive pulley (6) against spring pressure. The pulley
bracket (3) will retract and lock allowing removal/fitting of the belt. When the new belt is in position release the pulley bracket
by pushing in and holding the idle pulley, then press and hold the tension bar (5) whilst releasing the pressure on the idle pulley.
6.2.
The tracking of the belt can be altered by adjusted cross head screw (2).
fig.1
fig.2
S01046.V2 Issue 1 06/07/18
Original Language Version
© Jack Sealey limited
