background image

60W SOLDERING STATION 

 

MODEL NO: 

SD004 

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

1.1.    

ELECTRICAL  SAFETY

 

‰

  

WARNING!

 It is the user’s responsibility to check the following:

 

Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all    

 

electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical  

 

products. You may obtain an RCD by contacting your local Sealey stockist. 

 

If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable  

 

 

Appliance Test) tested.

 

Electrical safety information, it is important that the following information is read and understood.

1.1.1.   

Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. 

1.1.2.   

Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.

1.1.3. 

  

IMPORTANT

: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with 

the  

 

correct fuse - see fuse rating in these instructions.

 

8

   DO  NOT

 pull or carry the appliance by the power cable.

 

8

  

DO NOT

 pull the plug from the socket by the cable. 

 

8

   DO  NOT

 use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is 

  replaced immediately by a qualified electrician.

1.1.4. 

  

This product is fitted with a BS1363/A 13 Amp 3 pin plug. 

        

If the cable or plug is damaged during use, switch the electricity supply and remove from use. 

        

Ensure that repairs are carried out by a qualified electrician.

        

Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.

 

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

 

b) Connect the BROWN live wire to the live terminal ‘L’.

 

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

 

Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight. 

 

Sealey recommend that repairs are carried out by a qualified electrician. 

1.2 

  GENERAL SAFETY

 

‰

  

WARNING!

 

Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this  

 

 equipment.

 

9

   Familiarise yourself with the application, limitations and potential hazards of the soldering station.

 

9

   Replace or repair damaged parts. 

Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

 

9

   Locate soldering station in a suitable working area, keep area clean and tidy and free from unrelated materials.

 

9

   Keep the work area clean, uncluttered and ensure there is adequate lighting.

 

9

   Keep the soldering iron clean for best and safest performance.

 

9

   Ensure there are no flammable or combustible materials near the work area.

 

9

   Wear approved safety eye protection (standard spectacles are not adequate).

 

9

   Wear appropriate protective clothing.

 

9

   Ensure the workpiece is adequately held before operating the soldering iron.

 

9

   Always replace the soldering iron in its holder when not in use.

 

9

   Remove excess solder from the soldering iron by wiping the tip on a damp, natural sponge; not by abrupt force.

 

8

  

DO NOT

 attempt to remove excess solder from the soldering iron by shaking it. Hot solder may become airborne and land on skin    

  causing burns and blisters.

 

8

  

DO NOT

 allow children or pets into the area where the soldering is taking place.

 

8

  

DO NOT

 attempt to cool the iron with water.

 NOTE: 

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental   

 

capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in  

 

a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not  

 

be made by children without supervision.

Recommended fuse rating

3 Amp

S

D004            Issue 1          19/08/2019

Original Language Version

© Jack Sealey Limited

Refer to 

instructions

Hot surfaces

Indoor use  

only

Warning!

Wear eye 

protection

Содержание SD004

Страница 1: ...in plug If in doubt contact a qualified electrician a Connect the GREEN YELLOW earth wire to the earth terminal E b Connect the BROWN live wire to the live terminal L c Connect the BLUE neutral wire to the neutral terminal N Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight Sealey recommend that repairs are carried out by a qualified electrician ...

Страница 2: ... to the setting Switch is located on the side of the unit 4 2 2 The current set temperature will be displayed for 3 seconds 4 2 3 After a further 3 seconds the display will show the real time temperature of the tip and charging activity if heating is required NOTE The number of bars shown by the analogue current display fig 1 7 represent the current being applied to the tip 4 3 TEMPERATURE SETTING...

Страница 3: ...conds CAL will be displayed 4 5 5 After making any required adjustments press to save the setting 5 ERROR MESSAGES 5 1 If either of the two screens below are displayed turn the unit off and replace the heating element refer to section 7 2 H E indicates heating element failure S E indicates Sensor element failure 6 TEMPERATURE UNITS 6 1 To change the units used in the measurement of temperature hol...

Страница 4: ...d fluids according to local regulations WEEE REGULATIONS Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment WEEE When the product is no longer required it must be disposed of in an environmentally protective way Contact your local solid waste authority for recycling information Note It is our policy to continually...

Отзывы: