Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & SPECIFICATIONS
WARNING!
Turn off, or disconnect from, air supply before
servicing or performing any maintenance and when unit is not in
use.
Failure to comply with this instruction may damage the
unit and will invalidate your warranty.
WARNING!
Wear approved ear, eye, hand and respiratory
protection when operating the blaster. A full range of personal
safety equipment is available from your Sealey dealer.
Maintain correct balance and ensure firm footing.
Spillages of abrasive material, which may be slippery, must be
cleaned up immediately to avoid injury.
Locate blaster in a suitable, well ventilated, work area. Keep area
clean and tidy and free from unrelated materials, and ensure that
there is adequate lighting.
Maintain the blaster in good condition (use an authorised service
agent).
Replace or repair damaged parts. Use recommended parts only.
Non-authorised parts may be dangerous and will invalidate the
warranty.
Keep the unit clean for best and safest performance.
Remove ill fitting clothing. Remove ties, watches, rings, other
loose jewellery and contain long hair.
Always keep the blast nozzle directed at the workpiece.
If a failure or malfunction occurs
immediately disconnect from
air supply.
Keep all other persons away from the working area. Contact with
high pressure blast or inhaling the dust generated is dangerous.
DO NOT
use the blaster for any purpose other than that for
which it is designed.
DO NOT
operate the blaster if any parts are missing or damaged
as this may cause failure and/or personal injury.
DO NOT
use any abrasive which contains free silica.
We
recommend Sealey Shot Blasting Grit, item B/25KG.
DO NOT
attempt to clear a blocked nozzle while the unit is
pressurised.
DO NOT
allow untrained persons to operate the blaster.
DO NOT
get the blaster wet or use in damp or wet locations or
areas where there is condensation.
DO NOT
leave the blaster operating unattended.
DO NOT
operate the blaster when you are tired, under the
influence of alcohol, drugs or intoxicating medication.
DO NOT
stand or sit on the blaster.
DO NOT
direct air from the air hose at yourself or others.
DO NOT
operate system with air supply exceeding 125psi.
INSTRUCTIONS FOR:
SHOT BLASTERS WITH WATER
TRAP AND WHEELS 37/75ltr
MOdeL No's:
SB997 & SB998
3. AIR SUPPLY
WARNING!
ensure the air supply does not exceed 125psi
while operating the unit. Too high an air pressure will shorten
the life of the unit due to excessive wear and may cause
damage and/or personal injury.
3.1
ensure the blaster air valve (trigger) is in the ‘Off’ position
before connecting to the air supply.
3.2
Keep the air hose between the compressor and the unit a
reasonable length and install an air filter and water separator
(fig.1).
3.3
drain the air tank daily. Water in the air line will damage the
unit.
3.4
The recommended hook-up procedure is shown in fig.1.
3.5
The minimum hose diameter should be 1/4" I.d. and fittings
must have the same inside dimensions.
3.6
Use correct hoses and fittings.
3.7
Keep hoses away from heat, oil and sharp edges. Check
hoses for wear and ensure that all connections are
secure.
fig.1
SB997, SB998 Issue: 3 - 06/01/11
Pressured tank for maximum power with 2.4mtr rubber hose, four
ceramic nozzles and in-line water trap for moisture-free grit blasting.
Supplied with bayonet air line coupling and air flow regulator. Accepts
a variety of grits up to 80 microns and suitable for stripping rust and
paint from wheels, chassis, panels and other corroded/painted
surfaces.
Model:
SB997
SB998
Maximum Fill Weight:
46kg
92kg
Working Pressure:
60 ~ 125psi
Air Requirements:
6 ~ 25cfm
Air Inlet Size:
1/4” BSP
Nozzle sizes:
2, 2.5, 3, 3.5 & 5mm
Grit size:
80 micron
Maximum grit consumption:
180kg/hr
fig.2
SB997
Original Language Version
