8
DO NOT
point spray gun at yourself, at other persons or animals.
8
DO NOT
carry the by the air hose, or pull the hose from the air supply.
8
DO NOT
use the spray gun for any purpose other than for which it is designed.
8
DO NOT
allow untrained persons to operate the spray gun.
8
DO NOT
get the spray gun wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT
operate gun if any parts are missing or damaged as this may cause failure or personal injury.
8
DO NOT
direct air from the air hose at yourself or others.
9
When not in use switch the spray gun off, and disconnect from the air supply.
10. TYRE INfLATOR SAfETY
9
disconnect the gauge from the air supply before changing accessories, servicing or performing any maintenance.
9
maintain the
gauge in good condition (use an authorised service agent), and keep the gauge clean for best and safest performance.
9
Replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate
the warranty.
9
locate gauge in a suitable work area, keep area clean and tidy and free from unrelated materials and ensure there is adequate lighting.
9
Keep children and unauthorised persons away from the work area.
8
DO NOT
direct gauge outlet at yourself or at other persons or animals.
8
DO NOT
carry by the hose, or yank the hose from the air supply.
8
DO NOT
use the gauge for a task which it is not designed to perform.
8
DO NOT
operate the gauge when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
operate gauge if parts are missing or the gauge is damaged, as this may cause failure and/or personal injury.
11. AIR GUN SAfETY
WARNING!
disconnect blow gun from the air supply before changing accessories, servicing or performing any maintenance.
9
de-pressurise the blow gun before removing air hose from the gun.
9
maintain the blow gun in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Non genuine parts may be dangerous and will invalidate the warranty.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
only use the blow gun for the purpose of blowing compressed air.
WARNING!
Always wear approved eye or face protection when operating the blow gun. Use a
face or dust mask if dust is generated.
Wear appropriate protective clothing.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non slip shoes.
9
Remove ill fitting clothes, ties, watches, rings, other loose jewellery, and contain/tie back long hair.
9
Keep children and unauthorised persons away from the working area.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
WARNING!
air pressure should not exceed 90psi.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are secure.
8
DO NOT
use the blow gun for any purpose other than for which it is designed.
8
DO NOT
operate blow gun if any parts are damaged or missing as may cause failure or personal injury.
8
DO NOT
carry the by the hose, or yank the hose from the air supply.
8
DO NOT
allow untrained persons to operate the blow gun.
8
DO NOT
operate blow gun when you are tired, under influence of alcohol, drugs or intoxicating medication.
8
DO NOT
leave the blow gun operating whilst unattended.
8
DO NOT
direct air from the blow gun at yourself, others or animals.
9
When not in use disconnect from the blow supply and store in a safe, dry, child proof area.
12. INTRODUCTION
Kit contains: Gravity feed spray gun, tyre inflator, air blow
gun, 5m air hose1/4”BSP
13. SPECIfICATION
Rated air pressure for all tools in the Air kit ...................
90psi
max. working pressureof Pe Hose ................................
90bar
14. AIR SUPPLY
14.1.
R
ecommended hook-up fig.8.
14.1.1. ensure tool’s air valve (or trigger) is in the off position before connecting to the air supply.
WARNING!
Ensure the air supply is clean and does not exceed specification (above) while operating the tool. Too high an air pressure
and/or unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal
injury.
14.1.2. d
rain the air tank daily. Water in the air line will ruin the paint finish and damage the tool.
14.1.3. C
lean air inlet filter weekly.
14.1.4. l
ine pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4” I.D. and fittings must have the same inside dimensions.
14.1.5. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
14.2.
COUPLINGS
Vibration may cause failure if a quick change coupling is connected directly to the tool. To overcome this, connect
a leader hose. A quick change coupling may then be used to connect the leader hose to the air line recoil hose (fig.8).
fig.8
Original Language Version
© Jack Sealey limited
S
AC2420E.V3, SAC2420EPK.V2 Issue 1 13/06/19
