2. INTRODUCTION
SA800.V5
: Polycarbonate outer housing with soft rubber handgrip reduces chill and vibration. Features adjustable air regulator for additional
control and exhaust muffler to reduce noise emission. Model No. SA801 features dust-free outlet for use with centralised dust extraction
systems. All models supplied with hook-and-loop pad.
SA801.V5:
Polycarbonate outer housing with soft rubber hand grip reduces hand-chill and vibration with an overall weight of 0.7kg. Features
adjustable air regulator for additional control. Exhaust muffler to reduce noise emission. Dust-free outlet for use with centralised dust
extraction systems. Supplied with dust free hook-and-loop pad.
3. SPECIFICATION
Model No:..............................................................SA800.V5
Air consumption ........................................................... 16cfm
Free speed .............................................................10000rpm
Inlet size ....................................................................1/4”BSP
Operating pressure ....................................................... 90psi
Orbit size ..................................................................... Ø5mm
Pad size .................................................................. Ø150mm
Thread size .............................................................5/16”UNF
Noise power/pressure .................................. 100.3/89.3dB(A)
Vibration/uncertainty ........................................ 5.24/1.01m/s²
4. AIR ASSEMBLY
4.1.
AIR SUPPLY
4.1.1.
Ensure the sander air valve (or throttle is in the “Off” position before connecting to the air supply.
4.1.2.
You will require an air pressure and an air flow according to the specification above.
WARNING!
Ensure the air supply is clean and does not exceed 90psi while operating the sander.
4.1.3. Too high an air pressure and/or unclean air will shorten the product life due to excessive wear, and may be dangerous, causing
damage and/or personal injury.
4.1.4. Drain the air tank daily. Water in the air line will damage the sander and will invalidate your warranty.
4.1.5. Clean air inlet filter weekly. Recommended hook-up procedure (fig.1).
4.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
4.1.7. The minimum hose diameter should be 1/4” I.D. and fittings must have the same inside dimensions.
4.1.8. Keep hose away from heat, oil and sharp edges. Check hoses for wear and make certain that all connections are secure.
4.2.
COUPLINGS
4.2.1. Vibration may cause failure if a quick change coupling is connected directly to the air sander. To overcome this, connect a leader
hose to the sander. A quick change coupling may then be used to connect the leader hose to the air line r
ecoil hose (figs.1 & 2).
5. OPERATION
Part numbers refer to attached Parts List
5.1. USE OF TOOL
WARNING!
Disconnect from the air supply before carrying
out any of the adjustments below.
5.1.1.
Before each use of tool make sure that the pneumatic system
is not damaged. Damaged parts should be replaced before
use.
5.1.2. Dry the pneumatic system before use.
5.2.
SELECT FOR USE WITH BAG OR EXTRACTION
SYSTEM SA801.V5 ONLY
5.2.1.
Use exhaust key (46) to push in plunger on top of exhaust
valve (45) to select use: with bag (IN position) or use with
extraction system (OUT position).
5.3. FIT NEW PAD
5.3.1. Push supplied spanner between pad and sander and turn pad until nut is held. Undo nut anticlockwise. Spin on new pad and
tighten clockwise with spanner.
5.4.
FIT SANDING DISC
5.4.1. Disc should be placed concentrically. It is recommended to attach to disc the sanding sheet with holes cut out so that the holes
in the disc match the holes in shield. This will increase the efficiency of removal of dust created during operation.
IMPORTANT!
Before attachment of the sanding discs you should check it for damage,
DO NOT
use damaged sanding discs.
5.5.
OPERATION OF THE SANDER
5.5.1. Depress valve lever to start the sander and allow the disk to reach its full speed, before use.
5.5.2. Speed is adjustable using the wheel below the lever.
SA801.V5
Original Language Version
© Jack Sealey Limited
fig.3
fig.1
fig.2
Model No:..............................................................SA801.V5
Air consumption ........................................................... 16cfm
Free speed .............................................................10000rpm
Inlet size ....................................................................1/4”BSP
Operating pressure ....................................................... 90psi
Orbit size ..................................................................... Ø5mm
Pad size .................................................................. Ø150mm
Thread size .............................................................5/16”UNF
Vacuum outlet ........................................................... Ø28mm
Noise power/pressure .................................. 100.3/89.3dB(A)
Vibration/uncertainty ........................................ 5.24/1.01m/s²
SA800.V5, SA801.V5 Issue 2 (H,F) 19/06/2020
