Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
p
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
p
WARNING!
Disconnect from air supply before refilling with staples, servicing or performing maintenance.
3
Maintain the stapler in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use genuine parts only. Non-authorised parts may be dangerous and
will invalidate the warranty.
3
Use in suitable clean and tidy work area, free from unrelated materials and ensure there is adequate lighting.
p
WARNING!
Always wear approved eye and/or face and hand protection when operating the stapler.
3
Remove ill fitting clothing. Remove ties, loose jewellery, and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the working area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the stapler. Never hold a workpiece by hand.
3
When the stapler is put down during pauses in operation ensure that the trigger catch slide is not depressed
by the weight of the stapler or by placing the stapler in a restricted position that could put pressure on the
trigger catch slide.
3
During extended breaks in operation disconnect the stapler from the air supply.
p
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 50-90psi.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this stapler may pose a health risk. It is the operators responsibility to
correctly assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective
equipment.
7
DO NOT point the staple discharge outlet at yourself or anyone else. Do not point at animals.
7
DO NOT use any power source except an air compressor.
7
DO NOT operate the stapler near any inflammable substance or on any container that once contained an
inflammable substance.
7
DO NOT use the stapler for a task it is not designed to perform.
7
DO NOT operate stapler if any parts are damaged or missing as this may cause failure and/or personal injury.
7
DO NOT carry the stapler by the hose, or yank the hose from the air supply.
7
DO NOT place the stapler close to your face and do not point at other persons or animals.
7
DO NOT operate stapler when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT carry the stapler with your finger on the trigger.
7
DO NOT direct air from the air hose at yourself or others.
3
When not in use, disconnect from air supply and store in a safe, dry, childproof location.
SA79R - 0016 - (1) - 260701
INSTRUCTIONS FOR
AIR OPERATED STAPLER
Model:
SA79R
01284 757500
E-mail:
01284 703534
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12
months from purchase date. proof of which will be required for any claim.
INFORMATION:
Call us for a copy of our latest catalogue
and promotions on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group
, Bury St. Edmunds, Suffolk.
ITEM PART NO. DESCRIPTION
1
SA79R/01 SCREW 5*22
2
SA79R/02 WASHER #5*1.1t
3
SA79R/03 EXHAUST COVER
4
SA79R/04 COMPRESSION SPRING
5
SA79R/05 SEAL AIR
6
SA79R/06 CYLINDER CAP
7
SA79R/07 O-RING 13.8*2.4
8
SA79R/08 WASHER 9*6*0.8
9
SA79R/09 HEAD VALVE PISTON
10
SA79R/10 PISTON STOPPER
11
SA79R/11 O-RING 31*2.5
12
SA79R/12 O-RING 25*3.5
13
SA79R/13 GASKET
14
SA79R/14 COLLAR
15
SA79R/15 CYLINDER
16
SA79R/16 BUMPER
17
SA79R/17 O-RING 39.4*3.1
18
SA79R/18 SPACER
19
SA79R/19 BODY
20
SA79R/20 NOZZLE
21
SA79R/21 O-RING 11*1.05
22
SA79R/22 O-RING 8*1
23
SA79R/23 UPPER REMOTE HOUSING
24
SA79R/24 CONICAL SPRING
ITEM PART NO. DESCRIPTION
49
SA79R/49 SPRING HOLDER
50
SA79R/50 COMPRESSION SPRING
51
SA79R/51 RELEASE CATCH
52
SA79R/52 DRIVER GUIDE
53
SA79R/53 DRIVER GUIDE COVER
54
SA79R/54 WASHER #4*1.2t
55
SA79R/55 SCREW 4*5.5
56
SA79R/56 CLICK LEVER.
57
SA79R/57 TORSION SPRING
58
SA79R/58 HEX. NUT M5
59
SA79R/59 STEP PIN DIAM 5*18.6
60
SA79R/60 SCREW M4
61
SA79R/61 PISTON SET
62
SA79R/62 PUSHER
63
SA79R/63 FEEDER SPRING
64
SA79R/64 MAGAZINE SET
65
SA79R/65 SCREW M6
66
SA79R/66 STEEL BAR
67
SA79R/67 CYLINDER CAP SET
68
SA79R/68 HEAD VALVE PISTON SET
69
SA79R/69 CYLINDER SET
70
SA79R/70 TRIGGER VALVE SET
71
SA79R/71 TRIGGER SET
ITEM PART NO. DESCRIPTION
25
SA79R/25 O-RING 1.9*1.2
26
SA79R/26 REMOTE CORE
27
SA79R/27 REMOTE HOUSING
28
SA79R/28 O-RING 9.8*1.9
29
SA79R/29 E-RING 2.5 DIAM
30
SA79R/30 STEP PIN DIAM 2.9*29
31
SA79R/31 EXTENSION SPRING
32
SA79R/32 TRIGGER GUIDE
33
SA79R/33 PIN BUSHING
34
SA79R/34 TRIGGER
35
SA79R/35 PIN 3*18.8
36
SA79R/36 CATCH GUIDE PLATE
37
SA79R/37 SPRING PIN 3*26
38
SA79R/38 O-RING 35*3.5
39
SA79R/39 TAIL COVER
40
SA79R/40 AIR PLUG
41
SA79R/41 O-RING 21.3*3
42
SA79R/42 PISTON HEAD
43
SA79R/43 DRIVER BLADE PIN
44
SA79R/44 OUTER SPRING PIN 4*10
45
SA79R/45 INNER SPRING PIN 2.5*10
46
SA79R/46 DRIVER BLADE
47
SA79R/47 SPACER
48
SA79R/48 SPACER
Issue Date:
26 0701
Issue No:
1
Date Modified:
N/A
