InstructIons For:
MICRO AIR DIE GRINDER
model no:
SA673
1. SAfETy
3. SpECIfICATION
4. CONTENTS
2. INTRODuCTION
sA673 Issue: 3(I) - 17/10/14
Original Language Version
© Jack sealey limited
IMPORTANT:
pLEASE READ THESE INSTRuCTIONS CAREfuLLy. NOTE THE SAfE OpERATIONAL REQuIREMENTS, WARNINGS & CAuTIONS. uSE THE
pRODuCT CORRECTLy AND WITH CARE fOR THE puRpOSE fOR WHICH IT IS INTENDED. fAILuRE TO DO SO MAy CAuSE DAMAGE AND/OR
pERSONAL INJuRy AND WILL INVALIDATE THE WARRANTy. KEEp THESE INSTRuCTIONS SAfE fOR fuTuRE uSE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
WARNING!
Wear
approved eye and ear protection. Wear appropriate Personal Protective equipment. A full range of PPe is available from your
sealey dealer.
Be aware of cosHH when it applies.
WARNING!
ensure Health & safety, local authority and general workshop practice regulations are adhered to when using this equipment.
WARNING!
disconnect from the air supply before changing the grinding wheel bit, servicing or performing maintenance.
WARNING!
ensure correct air pressure is maintained and not exceeded. recommended air line pressure is 90psi.
maintain the tool in good condition (use an authorised service agent).
replace damaged parts/bits. use genuine parts/bits only. unauthorised parts/bits may be dangerous and will invalidate the warranty.
use in a suitable clean and tidy work area, free from unrelated materials. ensure that there is adequate lighting and ventilation.
remove ill fitting clothing. remove ties, loose jewellery and contain and/or tie back long hair.
Keep children and unauthorised persons away from the work area.
Before each use, check the grinding bit is secure and sound. If worn or damaged, replace immediately.
ensure the workpiece is secure. never hold a workpiece in the hand; use a vice or clamps.
Keep the air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are
secure.
Prolonged exposure to vibration from this tool poses a health risk. It is the employer’s/owner’s responsibility to correctly assess the hazard
and issue guidelines for safe periods of use and offer suitable protective equipment. safety gloves are recommended.
When not in use,
disconnect from the air supply and store complete in the supplied case.
Wear breathing apparatus when fumes or dust pose a hazard. Be aware of and adhere to cosHH regulations.
DO NOT
Grind materials containing asbestos.
DO NOT
use any power source except an air compressor.
DO NOT
operate the tool near any inflammable
substance or on any container that has held an inflammable substance.
DO NOT
use the tool for a task it is not designed to perform.
DO NOT
operate the tool if unwell, tired or intoxicated.
DO NOT
carry the tool by the hose, or yank the hose from the air supply.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
Air motor with quality bearings for smooth and powerful operation. shrouded exhaust gives quieter operation. suitable for professional users.
supplied with spanners and grinding points, air tool oil, inline oiler and quick connector.
Model No:: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA673
collet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø3mm (1/8")
Free speed:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58000rpm
Air consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3cfm
operating Pressure:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90psi
noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82dBA
noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71dBA
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.56m/s²
uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.62m/s²
Item no Part no
description
Qty
1 Air
micro
Grinder
1
2
Grinding Wheel Bits
1 (set of 10)
3 Air
tool
oil 50ml
4
In line oiler
1
5 chuck
spanner
2
6 Quick
connector
1
7 carry
case 1
fig.1
1
2
4
6
3
5
7
refer to
instruction
manual
Wear eye
protection
Wear ear
protection