WARNING!
Disconnect die grinder from air supply before changing accessories, servicing or
performing maintenance.
Replace or repair damaged parts.
Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
5.1.
If air supply does not have an oiler, lubricate the air die grinder daily with a few drops of
Sealey air tool oil dripped into the air inlet to prolong its life.
5.2.
Clean the die grinder after use.
5.3.
Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or
type of hose connectors. To remedy check the air supply and follow instructions in
Section 3.
b) Grit or gum deposits in the die grinder may also reduce performance. If your model has
an air strainer (located in the area of the air inlet), remove the strainer and clean it. Flush
the die grinder out with gum solvent oil or an equal mixture of SAE No 10 oil and paraffin.
Allow to dry before use.
5.4.
For a full service contact your local Sealey service agent.
5.5.
When not in use, disconnect from air supply, clean die grinder and store in a safe, dry,
childproof location.
5.6.
Periodically lubricate crown and pinion gear with general purpose oil through the lubrication
point.
5. MAINTENANCE
4.2. Operating
WARNING!
Ensure you have read, understood and apply Section 1 safety instructions.
4.2.1. Connect the die grinder to the air supply as described in Section 3.
4.2.2. To start, hold firmly and push the trigger locking lever forward whilst depressing trigger.
4.2.3. The stone must be running at its maximum speed before attempting to grind the workpiece.
4.2.4. Slowly and smoothly bring the grinding stone toward the workpiece (avoid jerky
movements). Exert adequate pressure on the die grinder to grind according to the type and
size of the material you are working with. Avoid subjecting bit to excessive strain or harsh
impacts. Always hold die grinder firmly and ease grinding stone against workpiece. Maintain
a controlled progression.
DO NOT
allow die grinder to free run for an extended period of time as this will shorten its
life.
Risk of Hand Arm Vibration Injury.
The SA655 Air Die Grinder Maxi size 90° Premier when operated in accordance with these instructions and tested in accordance
with BS EN ISO 8662-13:1997 results in the following vibration emission declared in accordance with BS EN12096:1996.
Measured vibration emission value: ...................... 1.4m/s²
Uncertainty: ........................................... 0.56m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
This item represents a low Hand Arm Vibration risk
to users. The calculated maximum usage period exceeds 8 hours. We recommend appropriate safety equipment is utilised and
regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive strain injury.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Original Language Version
SA655 Issue: 1 - 06/09/11
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk,
email [email protected] or phone 01284 757500.