background image

1. 

SAFETY INSTRUCTIONS

 

Follow all workshop Health & Safety rules, regulations and conditions when using tool. 

 

WARNING!

 

Disconnect from air supply before changing cutting disc or servicing.

 

Maintain tool in good condition and replace any damaged or worn parts. 

Use genuine parts only.    

  Unauthorised parts may be dangerous and will invalidate the warranty.

 

WARNING!

 Check correct air pressure is maintained and not exceeded. We recommend 90psi.

  Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure  

  that all connections are secure.

 

WARNING! 

Before each use check cutting disc is secure and the disc is not worn or damaged. If damaged  

  replace immediately.

  Ensure replacement discs are not damaged in any way such as cracks, deformations or splinters etc. Also  

  check the mounting washer to ensure it is not deformed, burred or notched. Damaged washer must not be  

  used as it may cause irregular pressure on the disc which may cause the disc to break.

 DO NOT 

over tighten  

  a disc and never tamper with a disc in order to adapt it to a different size holder.

  Always use the correct disc suitable for the material being cut. Ensure the maximum speed specification of  

  the cutting disc is higher than that indicated on the machine data plate.

 

WARNING!

 Keep disc guard in place, tight and in good working order. The safety guard is a 

  mandatory fitting where tool is used in premises covered by the Health & Safety at Work Act.

 

WARNING! 

Always wear approved eye or face protection when operating the tool. 

  Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard.

  Wear ear defenders and gloves if necessary.

  Keep hands and body clear of the workpiece when operating the tool.

 

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

  Secure unstable workpiece with a clamp, vice or other adequate holding device. 

 

Keep children and non essential persons away from the working area.

 

Avoid subjecting disc to excessive strain, always ease disc down against workpiece (a harsh impact may  

  break the disc). 

DO NOT

 use force in order to cut workpiece. Maintain a controlled progression.

 

DO NOT

 get the tool wet or use in damp or wet locations.

 

DO NOT

 hold the workpiece by hand. Use clamps or a vice to secure the workpiece. 

 

DO NOT

 use the tool for a task it is not designed to perform.  

  WARNING! DO NOT

 use tool if damaged or faulty. Contact your local service agent.

 

DO NOT

 use tool unless you have been instructed in its use by a qualified person.

 

DO NOT

 position your body in line with the disc whilst cutting, and 

DO NOT

 remove the safety guard whilst  

  in use.

 

DO NOT

 carry the tool by the air hose, or yank the hose from the air supply. 

 

DO NOT

 direct air from the air hose at yourself or others.

 

WARNING!

 

DO NOT

 cut any materials containing asbestos.

 

DO NOT

 switch the tool on whilst the disc is in contact with the workpiece.

 

DO NOT

 allow workpiece to overheat. Cool using an oil lubricant.

 

DO NOT

 use tool where there are flammable liquids, solids or gases such as paint solvents, including waste  

  wiping or cleaning rags etc. as any sparks generated may be dangerous.

 

DO NOT

 touch the workpiece close to the ground surface as it will be very hot. Allow to cool. The workpiece  

  may also be very sharp. 

 

DO NOT

 operate tool if you are tired or under the influence of alcohol, drugs or intoxicating medication.

 

When not in use disconnect from air supply and store in a safe, dry, childproof location. 

Original Language Version

SA650.V3 Issue: 3(SP) - 20/11/13 

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, 

WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS 

INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. 

PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

INSTRUCTIONS FOR: 

AIR CUT-OFF TOOL 75MM

MODEL No: 

SA650.V3

© Jack Sealey Limited

Содержание SA650.V3

Страница 1: ...g area Avoid subjecting disc to excessive strain always ease disc down against workpiece a harsh impact may break the disc DO NOT use force in order to cut workpiece Maintain a controlled progression DO NOT get the tool wet or use in damp or wet locations DO NOT hold the workpiece by hand Use clamps or a vice to secure the workpiece DO NOT use the tool for a task it is not designed to perform WARN...

Страница 2: ...air line recoil hose see figs 1 2 3 PREPARING TOOL FOR USE 4 OPERATING INSTRUCTIONS fig 1 fig 2 2 INTRODUCTION SPECIFICATION Disc size Ø75mm Free speed 20 000rpm Air consumption 4cfm Operating pressure 90psi Air inlet size 1 4 BSP Weight 0 8kg Noise Power 103dB A Noise Pressure 92dB A Measured Vibration Emission Value 6 65m s Uncertainty Value 1 15m s Spare Disc Part No PTC 3C single PTC 3C5 Pack ...

Страница 3: ...y and ease disc against workpiece a harsh impact may break the disc Maintain a controlled progression DO NOT allow tool to free run for an extended period of time as this will shorten its life NOTE It is our policy to continually improve products and as such we reserve the right to alter data specifications and component parts without prior notice IMPORTANT No liability is accepted for incorrect u...

Страница 4: ...ude the operator the task and the inserted tool or consumable NB ensure that the length of leader hoses is sufficient to allow unrestricted use as this also helps to reduce vibration The state of maintenance of the tool itself is also an important factor a poorly maintained tool will also increase the risk of Hand Arm Vibration Syndrome Health surveillance We recommend a programme of health survei...

Отзывы: