Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
p
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
p
WARNING!
Disconnect from air supply before changing accessories or servicing.
3
Maintain the sander in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and
will invalidate the warranty.
3
Use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
3
Before each use check abrasive belt for condition. If worn or damaged replace immediately.
3
Use only the correct size and type of sanding belt with this sander.
3
Ensure there are no flammable or combustible materials near the work area.
p
WARNING!
Always wear approved eye or face and hand protection when operating the sander.
3
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.
3
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, rivets, etc.
3
Avoid unintentional starting.
3
Ensure the abrasive belt rating is the same as, or, greater than the RPM rating of the sander.
p
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this sander poses a health risk. It is the owners responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
7
DO NOT use the sander for a task it is not designed to perform.
7
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
p
WARNING!
DO NOT sand any materials containing asbestos.
7
DO NOT carry the sander by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to, the sander, let the sander do the work.
7
DO NOT switch the sander on whilst the belt is in contact with the workpiece.
7
DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and including
waste wiping or cleaning rags etc.
7
DO NOT carry the sander with your finger on the power lever.
7
DO NOT direct air from the air hose at yourself or others.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.
7
DO NOT get the sander wet or use in damp or wet locations, although the sanding disc may be used wet.
7
DO NOT place attachments close to your face and do not point at other persons or animals.
SA355A - 0016 - (1) - 160801
INSTRUCTIONS FOR :
AIR OPERATED
20mm BELT SANDER
Model:
SA355A
01284 757500
E-mail:
01284 703534
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12
months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group
, Bury St. Edmunds, Suffolk.
Item Part No.
Description
1
SA355A/01
Idle Pulley Bracket Assembly
1A
SA355A/01A
Set screw
1B
SA355A/01B
Spring
1C
SA355A/01C
Screw
2
SA355A/02
Idle Pulley Bracket Assembly
2A
SA355A/02A
Idle Pulley
2B
SA355A/02B
Bearing (B/686ZZ)
2C
SA355A/02C
Screw
2D
SA355A/02D
Spacer 10x13x3
2E
SA355A/02E
Ball Bearing Axle
3
SA355A/03
Spring
4
SA355A/04
Finger Pad Assembly
6
SA355A/06
Hex Socket Bolt 5x12
7
SA355A/07
Grinding Belt
8
SA355A/08
Washer
8A
SA355A/08A
Hex Socket Head Bolt
9
SA355A/09
Drive Pulley
10
SA355/10
Flat Shoe
11
SA355/11
Hex Socket Bolt 5x18
12
SA355/12
Dust Cover
13
SA355A/13
Guard body
14
SA355/14
Tension bar
15
SA355/15
Spring
16
SA355/16
Pin
17
SA355/17
Lever pin
18
SA355/18
Housing
19
SA355A/19
Ball bearing
Item
Part No.
Description
20
SA355/20
End plate, front
21
SA355/21
Spacer
22
SA355/22
Key, drive pulley
23
SA355A/23
Cap (A)
24
SA355A/24
Bearing (B/626ZZ)
25
SA355/25
End plate, rear
26
SA355/26
Cylinder
27
SA355/27
Vane
28
SA355/28
Rotor
29
SA355/29
Lever, throttle
30
SA355/30
Pin, lever
31
SA355/31
Body, valve
32
SA355/32
O-Ring, Upper valve body
33
SA355/33
O-Ring, Lower valve body
34
SA355/34
O-Ring, Upper valve stem
35
SA355/35
Stem, valve
36
SA355/36
O-Ring, Lower valve stem
37
SA355/37
Spring, valve
38
SA355/38
Deflector
39
SA355/39
Bush, Air inlet
40
SA355A/40
Hex wrench (4mm)
41
SA355A/41
Lock pin
SA355/B60G
Belt, 60 Grit (pack of 5)
SA355/B80G
Belt, 80 Grit (pack of 5)
SA355/B100G Belt, 100Grit (pack of 5)
SA355/B120G Belt, 120Grit (pack of 5)
Issue Date:
160801
Version No:
1
Date Modified:
n/a
