Sealey SA152, Инструкции, Страница: 1 / 2

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p
WARNING! Ensure that Health & Safety, local authority, and general workshop practice regulations are
adhered to when using this equipment.
p
WARNING! Disconnect from air supply before changing accessories or servicing.
3
Maintain the grinder in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
3
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
3
Before each use check abrasive disc for condition. If worn or damaged replace immediately.
3
Ensure that the speed rating (rpm) of the disc is the same as, or greater than, the speed rating of the grinder.
3
Ensure that there are no flammable or combustible materials near the work area.
p
WARNING! Always wear approved eye (or face) and hand protection when operating the grinder.
3
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, grinder noise level may exceed 85dB in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure that the workpiece is secure before operating the grinder. Never hold a workpiece by hand.
3
Check the workpiece to ensure there are no protruding screws, bolts, nuts etc.
3
Avoid unintentional starting.
p
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this grinder poses a health risk. It is the owner’s responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
7
DO NOT use the grinder for a task it is not designed to perform.
7
DO NOT operate grinder if any parts are damaged or missing as this may cause failure and/or personal injury.
p
WARNING! DO NOT grind any materials containing asbestos.
7
DO NOT carry the grinder by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to, the grinder, let the tool do the work.
7
DO NOT place air line attachments close to your face and do not point them at other people or animals.
7
DO NOT operate grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT use the grinder where there are flammable liquids, solids or gases, such as paint solvents and
including waste wiping or cleaning rags etc.
7
DO NOT carry the grinder with your finger on the power lever.
7
DO NOT direct air from the air line at yourself or others.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.
SA152 - 1 - 300805
01284 757500
E-mail: sales@sealey.co.uk
Web address: www.sealey.co.uk
01284 703534
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group , Bury St. Edmunds, Suffolk.
ITEM PART NO. DESCRIPTION
1 SA152.01 MOTOR HOUSING
2 SA152.02 SPRING PIN
3 SA152.03 AIR INLET
4 SA152.04 THROTTLE LEVER
5 SA152.05 PIN
6 SA152.06 VALVE
7 SA152.07 O-RING
8 SA152.08 SPRING
9 SA152.09 RUBBER SPACER
10 SA152.10 VALVE STEM
11 SA152.11 O-RING
12 SA152.12 PLUNGER
13 B/608ZZ BEARING, 608ZZ
14 SA152.14 REAR PLATE
15 SA152.15 ROTOR
16 SA152.16 ROTOR BLADE
17 SA152.17 SPRING PIN
18 SA152.18 CYLINDER
19 SA152.19 FRONT END PLATE
20 B/6201Z BEARING
21 SA152.21 GASKET
22 SA152.22 BEVEL GEAR
23 SA152.23 GEAR HOUSING
ITEM PART NO. DESCRIPTION
24 SA152.24 SPRING WASHER
25 SA152.25 SCREW
26 SA152.26 SPACER
27 SA152.27 SCREW
28 B/626ZZ BEARING, 626ZZ
29 SA152.29 RETAINING RING
30 SA152.30 BEVEL GEAR
31 SA152.31 WASHER
32 B/6202ZZ BEARING, 6202ZZ
33 SA152.33 SPINDLE
34 SA152.34 KEY
35 SA152.35 GASKET
36 SA152.36 RETAINER
37 SA152.37 DISC COVER
38 SA152.38 FLANGE
39 SA152.39 SPRING PIN
40 SA152.40 FLANGE NUT
41 SA152.41 ADJUSTING SCREW
42 SA152.42 ADJUSTING NUT
43 SA152.43 SCREW
44 SA152.44 INLET GUIDE
45 SA152.45 SPRING
46 SA152.46 GOVERNER SHAFT
ITEM PART NO. DESCRIPTION
47 SA152.47 PENDULUM
48 SA152.48 SPRING PIN
49 SA152.49 O-RING
50 SA152.50 SPRING
51 SA152.51 SAFETY BAR
52 SA152.52 SPRING PIN
53 SA152.53 EXHAUST DIFFUSER
54 SA152.54 HANDLE
55 SA152.55 PIN WRENCH
56 SA152.56 RETAINING RING
57 SA152.57 BUSHING
58 SA152.58 O-RING
59 SA152.59 SPRING
60 SA152.60 S’DLE STOP BUTTON
61 SA152.61 SET SCREW
62 SA152.62 O-RING
63 SA152.63 CLAMP
64 SA152.64 HOSE
65 SA152.65 EXHAUST HOSE
66 SA152.66 O-RING
PARTS LIST FOR: 100mm AIR ANGLE
GRINDER Model No: SA152
Issue: . . . . . . . . . . .1
Date Issued: .300805
DANGER OF FIRE/EXPLOSION HAZARD
o
o
WARNING! The grinding process can produce streams of sparks which are a potential source of ignition especially when grinding
metal.
7
7
DO NOT use the grinder where there are flammable liquids, solids or gases.
7
7
DO NOT allow grinder sparks to make contact with the operator’s clothing or any other fabric such as cleaning rags. Fabrics
contaminated with inflammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
3
3
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant in
preference to man-made fibres.
INSTRUCTIONS FOR:
100mm AIR ANGLE GRINDER
Model No: SA152