PRobLeM
PossIbLe cAuse
ReMedy
Jack will not lift
the load
Jack does not lift
high enough or
feels “spongy”
Jack lifts but will
not hold load
Jack will not lower
completely
1) Be sure to use jack with adequate capacity.
2) Top up oil level.
3) Check and close release valve.
4) Open release valve and air vent (if fitted) and pump the handle a few times. Close valve and re-try.
5) Return jack to local service agent.
1) Top up oil level.
2) Return jack to local service agent.
3) Open release valve and air vent (if fitted) and pump the handle a few times. Close valve and re-try.
4) Check and close release valve.
1) Check and close release valve.
2) lower jack, close release valve. Pull up lifting arm to full height by hand. Open the release valve to lower arm.
3) Open release valve and air vent (if fitted) and pump the handle a few times. Close valve and re-try.
4) Return jack to local service agent.
1) Contact local service agent.
2) Open release valve and air vent (if fitted) and pump the handle a few times. Close valve and re-try.
3) Check and fully open release valve.
1) Overloaded
2) Oil level low
3) Release valve not correctly closed
4) Air in system
5) Packing worn or defective
1) Oil level low
2) Worn seals
3) Air in system
4) Release valve not closed
1) Release valve partially open
2) dirt on valve seats
3) Air in system
4) Faulty seals
1) Ram damaged
2) Air in system
3) Release valve partially open
3.3. Lowering
3.3.1. Raise the vehicle so that the axle stands can be removed, then lower the vehicle making sure that there are no persons or obstacles
beneath the vehicle, or in the path of its descent.
3.3.2. The lowering speed is controlled by
the amount the release valve (1) is opened. Turn valve anti-clockwise and lower slowly and carefully.
4. MAINteNANce
5. tRoubLeshootING
6. decLARAtIoN of coNfoRMIty
ImpoRtANt:
only fully qualified personnel should attempt maintenance or repair.
WARNING:
Do Not
use brake fluid, or any fluid other than Sealey hydraulic jack fluid, as to do so may cause serious damage to
the jack and will invalidate the warranty!
4.1. When the jack is not in use, the ram and piston must be in their lowest positions to minimise corrosion. Remove the handle to inactivate
jack.
4.2. Keep the jack clean and lubricate all moving parts with acid free oil on a regular basis.
4.3. To check oil level, fully lower the jack. Remove filler plug. The correct oil level is to the bottom of the filler opening.
4.4. After a year of extensive use, the oil should be replaced in order to extend the life of the jack. drain the oil through the filler plug
opening. Make sure that no dirt is allowed to enter the jack or the fresh oil.
4.5. To replace the oil, fill as required. Pump (unloaded jack) 5 or 6 times to expel air. Pump jack to full height and pour off excess oil
before refitting plug.
Note:
Ensure waste oil is disposed of in accordance with local authority regulations.
4.6. Before each use check for broken, cracked, bent, or loose parts. Also check for any visible damage to welds, ram, pump, body and
base. If any suspect item is found remove jack from service and take the necessary action to remedy the problem.
do Not
use the jack if believed to have been subjected to abnormal load or shock. Inspect and take appropriate action.
4.7. Periodically check the pump piston and piston rod for signs of corrosion. Clean exposed areas with a clean oiled cloth.
ImpoRtANt:
No RESpoNSIBILItY IS ACCEptED FoR INCoRRECt USE oF tHE JACK.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
Do Not REtURN JACKS
to US.
Please telephone 01284 757500 to obtain address and ‘phone number of your local agent. If jack is under guarantee please contact
your dealer.
de-commissioning:
draw off the oil into an approved container and dispose of the jack and the oil according to local regulations.
declaration of conformity
We, the sole importer into the UK, declare that the product listed below is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national
authority, upon request to Jack Sealey ltd.
ForJack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
yankee bottle Jack
Model: sJ50
2006/42/EC Machinery directive
93/68/EEC CE Marking directive
Signed by Mark Sweetman
17th March 2009
01284 757500
01284 703534
sole uk distributor
sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
NotE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPoRtANt:
No liability is accepted for incorrect use of this product.
WARRANty:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INfoRMAtIoN:
For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
SJ50 Issue: 2 - 17/03/09