30 & 50TONNE FLOOR TYPE PREMIER AIR/
HYDRAULIC PRESS
MODEL NO:
PPF301S, PPF501S
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Familiarise yourself with the applications, limitations and hazards of the press.
9
Maintain the press in good condition (use an authorised service agent).
9
Replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the press clean for best and safest performance.
9
Locate the press in a suitable work area, on a surface that is stable, level, dry, not slippery, and capable of sustaining the load.
9
Keep area clean and tidy and free from unrelated materials, and ensure there is adequate lighting.
WARNING!
Always wear approved eye or face protection when operating the press.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
9
Keep hands and body clear of the work table when operating the press.
9
Maintain correct balance and footing.
DO NOT
over reach. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
8
DO NOT
use the press for a task it is not designed to perform.
8
DO NOT
adjust or tamper with the safety valve, or make any modifications to the press.
8
DO NOT
exceed the rated capacity of the press. Avoid applying excessive force, use the pressure gauge to determine the applied
load.
8
DO NOT
apply off-centre loads. Ensure that workpiece is centrally loaded and correctly secured before operating the press.
8
DO NOT
allow the workpiece or the V blocks plates to fall from the press work bench.
8
DO NOT
get the press wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT
operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
climb upon the press.
8
DO NOT
use if bent, broken, cracked, leaking or otherwise damaged, or if press has been subjected to a shock load.
8
DO NOT
operate the press if any parts are missing as this may cause failure and/or possible personal injury.
8
DO NOT
use the press to compress a spring or any other item that could disengage and cause a potential hazard.
8
DO NOT
stand directly in front of loaded press and never leave loaded press unattended.
8
DO NOT
allow untrained persons to operate the press.
▲
DANGER!
This model is purpose designed to withstand greater loads than the hydraulic unit can develop. For safety reasons, always
ensure the workpiece and press tools are secured on the table and will not flex or suddenly give way, causing danger to operator or
the workpiece.
WARNING! DO NOT use brake fluid, or any fluid other than a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL, as
this may cause serious damage to the press and will invalidate the warranty.
9
When not in use, release pressure from the pump and clean the press. Stand or store the V blocks in a safe, childproof location.
WARNING!
The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
2. INTRODUCTION
Heavy-duty steel frame construction with integral air motor powering hydraulic pump unit. Screw adjustable ram and adjustable work area
with removable tray. Sliding hydraulic ram assembly giving 280mm of lateral travel for off-centre pressing applications. Frame head fitted with
ram pressure gauge. Winch assisted press table adjustment. Storage for press pins included in frame. Supplied with press pins, flat pressing
plate/V-blocks.. 2 Year guarantee*. This item is heavy. Extra assistance must be provided at the delivery point to help its safe delivery.
PPF301S, PPF501S Issue:2 (3)27/06/22
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear a face
shield
Wear protective
gloves
Wear safety
footwear
Wear protective
clothing
Warning
crushing
of hands
No reaching
in
Place V block
correctly
Piston rod
should face the
workpiece
